2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1500 Fuel Sender Open Detected

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is output when the combination meter detects a fuel sender gauge malfunction via the CAN.
DTC Code
DTC Detection Condition
Trouble Area
B1500
When the combination meter detects a fuel sender gauge malfunction.
  1. Harness or connector
  2. Combination meter assembly
  3. Fuel suction with pump and gauge tube assembly
  4. Fuel sender gauge assembly

WIRING DIAGRAM

E197359E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)
  1. Operate the intelligent tester according to the display and select the Data List (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5
    Fuel sender input value
    Unit: L

    OK:
    Fuel value displayed on the intelligent tester is almost the same as needle indication.

    Result 
    Result
    Proceed to
    NG
    A
    OK (w/ Multi-information Display)
    B
    OK (w/o Multi-information Display)
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


2. CHECK HARNESS AND CONNECTOR (COMBINATION METER - PUMP AND GAUGE AND BODY GROUND)
E157220E02
  1. Disconnect the E7 and E8 combination meter assembly connectors.

  1. Disconnect the N1 fuel suction with pump and gauge tube assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-9 (L) - N1-2 (FS)
    Always
    Below 1 Ω
    E8-21 (E) - N1-3 (FE)
    Always
    Below 1 Ω
    E7-15 (ET) - Body ground
    Always
    Below 1 Ω
    E8-9 (L) or N1-2 (FS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
E158805E05
  1. Remove the fuel sender gauge assembly.

    HINT:
    1. for 1GR-FE (Click here)
    2. for 2UZ-FE (Click here)
    3. for 3UR-FE (Click here)
    4. for 1VD-FTV (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2 (FS)
    Always
    Below 1 Ω
    A-3 (FE) - B-1 (FE)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Fuel Suction with Pump and Gauge Tube Assembly)
    *2
    Connector A
    *3
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 2UZ-FE)
    C
    NG (for 3UR-FE)
    D
    NG (for 1VD-FTV)
    E



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

C
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

D
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

E
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
A


4. INSPECT FUEL SENDER GAUGE ASSEMBLY
E154367E02
  1. Remove the fuel sender gauge assembly.

    HINT:
    1. for 1GR-FE (Click here)
    2. for 2UZ-FE (Click here)
    3. for 3UR-FE (Click here)
    4. for 1VD-FTV (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (FS) - 1 (FE)
    Float level is F (upper)
    13.5 to 16.5 Ω
    Float level is E (lower)
    405.5 to 414.5 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Fuel Sender Gauge Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 2UZ-FE)
    C
    NG (for 3UR-FE)
    D
    NG (for 1VD-FTV)
    E



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

E
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A


5. CHECK COMBINATION METER TYPE
  1. Check the combination meter type

    Result 
    Result
    Proceed to
    w/ Multi-information Display
    A
    w/o Multi-information Display
    B



B
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2012)B1500 Fuel Sender Open Detected (from Jan 2012) →