2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REASSEMBLY

Removal / installation · Vehicles built from Jan 2012


1. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.

  1. Using an E8 "TORX" socket wrench, install the stud bolts.

    Torque:
    for stud bolt A:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    for stud bolt B:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


    A142822E06
    Text in Illustration 
    *a
    Upper Side
    *b
    Lower Side


2. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
  1. Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzles with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


3. INSTALL PISTON WITH PIN SUB-ASSEMBLY

  1. A228439E01
    Using a screwdriver, install a new snap ring on one side of the piston pin hole.
    Text in Illustration 
    *1
    Service Cutout

    HINT:
    Be sure that the end gap of the snap ring is not aligned with the service cutout of the piston.

  1. Gradually heat the piston to approximately 80°C (176°F).

  1. Coat the piston pin and connecting rod with engine oil.

  1. A218911E01
    Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.
    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2
    *1
    Front Mark

    NOTICE:
    For the LH side, perform the assembly so that the front marks of the piston and connecting rod are on the same side. For the RH side, perform the assembly so that the front marks of the piston and connecting rod are on opposite sides.

    HINT:
    The piston and pin are a matched set.

  1. Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

  1. A228439E01
    Using a small screwdriver, install a new snap ring at the other end of the piston pin hole.
    Text in Illustration 
    *1
    Service Cutout

    HINT:
    Be sure that the end gap of the snap ring is not aligned with the cutout of the piston.


4. INSTALL PISTON RING SET

  1. A164414E02
    Install the oil ring (expander) and 2 side rails by hand.
    Text in Illustration 
    *1
    Upper Side Rail
    *2
    Oil Ring Expander
    *3
    Lower Side Rail

  1. A228397E01
    Using a piston ring expander, install the 2 compression rings with the paint mark on the right side.

    Paint Mark:
    Item
    Paint Mark
    No. 1
    Blue
    No. 2
    Orange

    Text in Illustration 
    *1
    Paint Mark
    *2
    No. 1 Compression Ring
    *3
    No. 2 Compression Ring
    V100135
    Right Side

  1. A174175E02
    Position the piston rings so that the ring ends are as shown in the illustration.
    Text in Illustration 
    *1
    Front Mark
    *2
    Upper Side Rail
    *3
    Lower Side Rail
    *4
    No. 1 Compression Ring
    *5
    No. 2 Compression Ring


5. INSTALL CRANKSHAFT BEARING

A124282E20

NOTICE:
Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.

Text in Illustration 
*1
No. 1 and No. 5 Journal Bearings
*2
No. 2, No. 3 and No. 4 Journal Bearings
  1. Clean each main journal and bearing.

  1. Install the upper bearing.

    1. A142825E02
      Install the upper bearing to the cylinder block.
      Text in Illustration 
      *1
      Oil Groove
      *2
      Oil Feed Hole
      *a
      CORRECT
      *b
      INCORRECT

      NOTICE:
      1. Do not apply engine oil to the bearings or contact surfaces.
      2. Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.
      3. Do not allow coolant to come into contact with the inner surface of the bearing.
      4. If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.

  1. Install the lower bearings.

    1. A149045E05
      Install the lower bearings to the crankshaft bearing caps.
      Text in Illustration 
      *1
      Vernier Caliper

    2. Using a vernier caliper, measure the distance between the edge of the crankshaft bearing cap and the edge of the lower bearing.

      Dimension A - B or B - A:
      0 to 0.7 mm (0 to 0.0276 in.)

      NOTICE:
      1. Do not apply engine oil to the bearings or contact surfaces.
      2. Do not allow coolant to come into contact with the inner surface of the bearing.
      3. If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.


6. INSTALL CRANKSHAFT THRUST WASHER SET

  1. A150072E01
    Apply engine oil to the thrust washer set.
    Text in Illustration 
    *1
    Oil Groove

  1. Install the 4 thrust washers to the No. 3 journal position of the cylinder block and bearing cap with the oil grooves facing outward.


7. INSTALL CRANKSHAFT

  1. A160708E02
    Apply new engine oil to the upper bearing and lower bearing, then place the crankshaft on the cylinder block.
    Text in Illustration 
    *1
    Number Mark

  1. Confirm the front marks and numbers of the main bearing caps and install the bearing caps to the cylinder block.

    HINT:
    A number is marked on each main bearing cap to indicate the installation position.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. Temporarily install the 10 main bearing cap bolts to the inside positions.

  1. A160709E02
    Insert the main bearing cap by hand until the clearance between the main bearing cap and cylinder block is less than 6 mm (0.236 in.) and partially tighten the 2 inner bearing cap bolts.

    Bolt length:
    91 mm (3.58 in.)

    Text in Illustration 
    *a
    Less than 6 mm

  1. A142799E01
    Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.

  1. Apply a light coat of engine oil to the threads and under the heads of the 10 main bearing cap bolts.

  1. A228398E01
    Temporarily install the 10 main bearing cap bolts to the outside positions.

    Bolt length:
    79.5 mm (3.13 in.)

  1. Tighten the main bearing cap bolts.

    HINT:
    The main bearing cap bolts are tightened in 2 progressive steps.


    1. A160706E04
      Step 1:
      Uniformly tighten the 20 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      for inner bolts:
      61 N*m{ 622 kgf*cm , 45 ft.*lbf }
      for outer bolts:
      27 N*m{ 275 kgf*cm , 20 ft.*lbf }

      If any of the main bearing cap bolts does not meet the specified torque, replace it.

    2. Mark the front of the bearing cap bolts with paint.

    3. Step 2:
      Tighten the bearing cap bolts 90° in the order shown in step 1.

    4. Check that the painted marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

  1. A160711E02
    Install and uniformly tighten the 10 main bearing cap bolts and 10 new seal washers in several steps in the sequence shown in the illustration.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

  1. Check that the crankshaft turns smoothly.


8. INSTALL CONNECTING ROD BEARING

  1. A228399E01
    Install the bearing to the connecting rod cap.
    Text in Illustration 
    *1
    Vernier Caliper
    *2
    Connecting Rod Cap
    *3
    Connecting Rod Bearing

    NOTICE:
    1. Clean the contact surfaces of the bearing and connecting rod cap.
    2. Do not apply engine oil to the bearing or the surface it contacts.

  1. Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.

    Dimension A - B or B - A:
    0 to 0.7 mm (0 to 0.0276 in.)

  1. A228400E01
    Install the bearing to the connecting rod.
    Text in Illustration 
    *1
    Vernier Caliper
    *2
    Connecting Rod
    *3
    Connecting Rod Bearing

    NOTICE:
    1. Clean the contact surface of the bearing and connecting rod.
    2. Do not apply engine oil to the bearing or the surface it contacts.

  1. Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing edge.

    Dimension A - B or B - A:
    0 to 0.7 mm (0 to 0.0276 in.)


9. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A163458
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.020 to 0.220 mm (0.000787 to 0.00866 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Standard thrust washer thickness:
    2.44 to 2.49 mm (0.0961 to 0.0980 in.)

    If necessary, replace the crankshaft.


10. INSTALL PISTON AND CONNECTING ROD
  1. Apply engine oil to the cylinder walls, pistons and surfaces of the connecting rod bearings.

  1. A174175E02
    Check the positions of the piston ring ends.
    Text in Illustration 
    *1
    Front Mark
    *2
    Upper Side Rail
    *3
    Lower Side Rail
    *4
    No. 1 Compression Ring
    *5
    No. 2 Compression Ring

    NOTICE:
    Do not align the ring ends.

    HINT:
    The expander ends can be placed anywhere.

  1. A214552E02
    Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.
    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2
    *1
    Front Mark

  1. Place the connecting rod cap on the connecting rod.

    1. A218936E01
      Match the numbered connecting rod cap with the connecting rod.
      Text in Illustration 
      *A
      for Bank 1
      *B
      for Bank 2
      *1
      Front Mark
      V100135
      Front

    2. Check that the front mark of the connecting rod cap is facing the proper direction.

      Front Mark:
      Item
      Front Mark
      LH
      Front Side
      RH
      Rear Side

  1. Install the connecting rod cap bolts.

    HINT:
    The connecting rod cap bolts are tightened in 2 progressive steps.


    1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.

    2. Temporarily install the connecting rod cap bolts.

    3. A214339
      Step 1:
      Install and alternately tighten the bolts of each connecting rod cap in several steps.

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    4. Mark the front side of each connecting rod cap bolt with paint.

    5. Step 2:
      Tighten the cap bolts 90°.

    6. Check that the paint marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.

← REPLACEMENT (from Jan 2012)ON-VEHICLE INSPECTION (from Sep 2011) →