2011-2013 Land Cruiser · Service Manual Power Source / Network

TERMINALS OF ECU

System information · Vehicles built from Sep 2011


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
A178856E02
  1. Disconnect the 2D, E1, E2 and E3 ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E2-1 (AM2) - 2D-62 (GND2)
    W - W-B
    Battery power supply
    Always
    11 to 14 V
    E1-6 (AM1) - 2D-62 (GND2)
    W - W-B
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK MASTER SWITCH (for Models with Jam Protection Function on 4 Windows)
B158007E07
  1. Disconnect the I11*1 or I22*2 master switch connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

    for LHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I11-11 (B) - I11-12 (GND)
    L - W-B
    Ignition power supply
    Ignition switch off
    Below 1 Ω
    I11-11 (B) - I11-12 (GND)
    L - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    I11-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    for RHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I22-11 (B) - I22-12 (GND)
    L - W-B
    Ignition power supply
    Ignition switch off
    Below 1 Ω
    I22-11 (B) - I22-12 (GND)
    L - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    I22-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK FRONT POWER WINDOW REGULATOR MOTOR LH
B158006E21
  1. Disconnect the I12 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I12-2 (B) - I12-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    I12-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
B158006E22
  1. Disconnect the I4 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I4-2 (B) - I4-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    I4-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)
B158006E23
  1. Disconnect the J11 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J11-2 (B) - J11-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    J11-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)
B158006E24
  1. Disconnect the J4 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J4-2 (B) - J4-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    J4-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK SLIDING ROOF ECU (w/ Sliding Roof System)
B160074E07
  1. Disconnect the R5 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R5-1 (B) - R5-2 (E)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    R5-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B122343E15
  1. Disconnect the E29 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E29-1 (+B) - E29-17 (E)
    B - W-B
    Battery power supply
    Always
    11 to 14 V
    E29-17 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ID CODE BOX (IMMOBILISER CODE ECU)
B161789E02
  1. Disconnect the E28 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E28-1 (+B) - E28-8 (GND)
    B - W-B
    Battery power supply
    Always
    11 to 14 V
    E28-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK STEERING LOCK ECU
B176026E02
  1. Disconnect the E26 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E26-7 (B) - E26-1 (GND)
    R - W-B
    Battery power supply
    Always
    11 to 14 V
    E26-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK AIR CONDITIONING AMPLIFIER (for 4-ZONE Type)
E132519E05
  1. Disconnect the E36 amplifier connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E36-5 (IG+) - E36-1 (GND)
    G - W-B
    IG power supply
    Ignition switch off
    Below 1 V
    E36-5 (IG+) - E36-1 (GND)
    G - W-B
    IG power supply
    Ignition switch ON
    11 to 14 V
    E36-6 (+B1) - E36-1 (GND)
    R - W-B
    Battery power supply
    Always
    11 to 14 V
    E36-7 (+B2) - E36-1 (GND)
    R - W-B
    Battery power supply
    Always
    11 to 14 V
    E36-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK AIR CONDITIONING AMPLIFIER (except 4-ZONE Type)
B160781E01
  1. Disconnect the E81 amplifier connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E81-21 (+B) - E81-14 (GND)
    R - W-B
    Battery power supply
    Always
    11 to 14 V
    E81-1 (IG+) - E81-14 (GND)
    G - W-B
    IG power supply
    Ignition switch ON
    11 to 14 V
    E81-1 (IG+) - E81-14 (GND)
    G - W-B
    IG power supply
    Ignition switch off
    Below 1 V
    E81-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK FRONT AIR CONDITIONING CONTROL PANEL (w/o Navigation System)
E160508E01
  1. Disconnect the F10 panel connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F10-7 (IG+) - F10-1 (GND)
    G - W-B
    IG power supply
    Ignition switch ON
    11 to 14 V
    F10-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK REAR AIR CONDITIONING CONTROL PANEL
E137024E05
  1. Disconnect the E55 panel connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E55-6 (IG) - E55-1 (E)
    G - W-B
    IG power supply
    Ignition switch ON
    11 to 14 V
    E55-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK RAIN SENSOR (w/ Rain Sensor)
E139261E05
  1. Disconnect the R11 rain sensor connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R11-4 (SIG) - Body ground
    G - Body ground
    IG signal circuit (to IG relay)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    R11-1 (ES) - Body ground
    W - Body ground
    Ground circuit
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK WINDSHIELD WIPER ECU (w/ Rain Sensor)
E157213E02
  1. Disconnect the E83 and E85 ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E83-5 (IG1l) - E83-6 (ES)
    G - B
    Power source
    Ignition switch ON
    11 to 14 V
    E85-10 (E) - Body ground
    W-B - Body ground
    Power ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

← PROBLEM SYMPTOMS TABLE (from Sep 2011)DTC CHECK / CLEAR (from Sep 2011) →