2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1468/68 Rear Passenger Side Room Temperature Sensor Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The rear room temperature sensor RH*1 or LH*2 (for front passenger side) is installed in the rear quarter trim board RH*1 or LH*2 to detect the rear room temperature and control the heater and air conditioner "auto" mode. The resistance of the rear room temperature sensor RH*1 or LH*2 changes in accordance with the rear room temperature for RH*1 or LH*2 seat. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier applies a voltage (5 V) to the rear room temperature sensor RH*1 or LH*2 and reads voltage changes as changes in the resistance of the rear room temperature sensor RH*1 or LH*2.
DTC Code
DTC Detection Condition
Trouble Area
B1468/68
An open or short in the rear room temperature sensor RH*1 or LH*2 circuit.
  1. Rear room temperature sensor RH*1
  2. Rear room temperature sensor LH*2
  3. Harness or connector between rear room temperature sensor RH and air conditioning amplifier assembly*1
  4. Harness or connector between rear room temperature sensor LH and air conditioning amplifier assembly*2
  5. Air conditioning amplifier assembly

HINT:
*1: for LHD
*2: for RHD


WIRING DIAGRAM

E156584E42
E156584E43

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (AIR CONDITIONER)
  1. Use the Data List to check if the rear room temperature sensor RH*1 or LH*2 is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor (RP)
    Rear room temperature sensor for RH*1 or LH*2 /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual rear room temperature for RH*1 or LH*2 displayed
    Open in the circuit: -6.5°C (20.3°F).
    Short in the circuit: 57.25°C (135.05°F).

    HINT:
    *1: for LHD
    *2: for RHD

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

2. INSPECT REAR ROOM TEMPERATURE SENSOR
E160595E03
  1. for LHDRemove the rear room temperature sensor RH (Click here).

  1. for RHDRemove the rear room temperature sensor LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 2 (-)
    10°C (50°F)
    3.00 to 3.73 kΩ
    15°C (59°F)
    2.45 to 2.88 kΩ
    20°C (68°F)
    1.95 to 2.30 kΩ
    25°C (77°F)
    1.60 to 1.80 kΩ
    30°C (86°F)
    1.28 to 1.47 kΩ
    35°C (95°F)
    1.00 to 1.22 kΩ
    40°C (104°F)
    0.80 to 1.00 kΩ
    45°C (113°F)
    0.65 to 0.85 kΩ
    50°C (122°F)
    0.50 to 0.70 kΩ
    55°C (131°F)
    0.44 to 0.60 kΩ
    60°C (140°F)
    0.36 to 0.50 kΩ

    NOTICE:
    Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE REAR ROOM TEMPERATURE SENSOR RH (Click here)

C
REPLACE REAR ROOM TEMPERATURE SENSOR LH (Click here)
A


3. CHECK HARNESS AND CONNECTOR (REAR ROOM TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)
E160312E11
E160312E12
  1. for LHD

    1. Disconnect the z56 sensor connector.

    2. Disconnect the E35 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z56-2 (-)- E35-2 (SG-6)
      Always
      Below 1 Ω
      z56-1 (+) - E35-19 (TR7)
      E35-2 (SG-6) - Body ground
      Always
      10 kΩ or higher
      E35-19 (TR7) - Body ground

  1. for RHD

    1. Disconnect the z55 sensor connector.

    2. Disconnect the E35 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z55-2 (-) - E35-2 (SG-6)
      Always
      Below 1 Ω
      z55-1 (+) - E35-18 (TR)
      E35-2 (SG-6) - Body ground
      Always
      10 kΩ or higher
      E35-18 (TR) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← B1467/67 Rear Air Foot Duct Sensor Circuit on Driver Side (from Jan 2012)B1468/68 Rear Passenger Side Room Temperature Sensor Circuit (from Jan 2012) →