2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 ''TORX'' driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.


2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B180836E05
    Apply MP grease to the sliding and rotating areas of the window regulator.

    NOTICE:
    Do not apply grease to the spring of the window regulator.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Loosely install the temporary bolt onto the window regulator.

  1. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

    NOTICE:
    Be careful not to drop the window regulator as it may become damaged.

  1. Temporarily install the window regulator with the 5 bolts.

  1. Tighten the 6 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

  1. B183141
    Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Be careful not to damage the glass.

  1. B180832
    Install the door glass to the window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


4. INSTALL FRONT DOOR SERVICE HOLE COVER

  1. B180831
    Apply butyl tape to the door.

  1. Pass the front door lock remote control cable and front door inside locking cable through a new front door service hole cover.

    NOTICE:
    1. When installing the service hole cover, pull the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. B186231E01
    Connect the 2 connectors.

  1. Attach the 9 clamps.

  1. Install the bolt as shown in the illustration.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


5. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

  1. B181519
    Connect the speaker connector.

  1. Install the speaker with the 4 screws.

    NOTICE:
    Do not touch the cone part of the speaker.


6. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.

  1. B183139
    Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. B180821
    Attach the 4 claws and 13 clips to install the front door trim board sub-assembly.

  1. Install the 3 screws.


7. INSTALL DOOR ASSIST GRIP COVER

  1. B183138
    Attach the 8 claws to install the door assist grip cover to the door trim panel.


8. INSTALL FRONT DOOR ARMREST BASE PANEL ASSEMBLY
  1. Connect the connector.

  1. B183137
    Attach the 5 claws to install the armrest base panel.


9. INSTALL FRONT DOOR INSIDE HANDLE BEZEL

  1. B183136
    Attach the 4 claws to install the bezel.


10. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH

  1. B180820
    Attach the clip and claw, and install the front door lower frame bracket garnish.


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSPECTION (from Sep 2011)INSTALLATION (from Jan 2012) →