2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSPECTION

Inspection · Vehicles built from Sep 2011

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)

  1. B175750E18
    Apply positive (+) battery voltage to the connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Condition
    Specified Condition
    1. Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.
    2. With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.
    Motor gear rotates clockwise (Up)
    1. Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.
    2. With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.
    Motor gear rotates counterclockwise (Down)

    1. If the result is not as specified, replace the regulator motor assembly.

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

    Text in Illustration 
    *1
    Motor Gear
    *a
    Component without harness connected
    (Front Power Window Regulator Motor Assembly LH)
    *b
    Clockwise
    *c
    Counterclockwise


INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)

  1. B180611E17
    for Models with Jam Protection Function on 4 Windows:
    Apply positive (+) battery voltage to the connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    1. Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.
    2. With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.
    Motor gear rotates counterclockwise (Up)
    1. Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.
    2. With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.
    Motor gear rotates clockwise (Down)

    1. If the result is not as specified, replace the regulator motor assembly.

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

    Text in Illustration 
    *1
    Motor Gear
    *a
    Component without harness connected
    (Front Power Window Regulator Motor Assembly RH)
    *b
    Clockwise
    *c
    Counterclockwise


INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on Driver Door Window Only)

  1. B175750E18
    Apply positive (+) battery voltage to the connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Condition
    Specified Condition
    1. Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.
    2. With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.
    Motor gear rotates clockwise (Up)
    1. Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.
    2. With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.
    Motor gear rotates counterclockwise (Down)

    1. If the result is not as specified, replace the regulator motor assembly.

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

    Text in Illustration 
    *1
    Motor Gear
    *a
    Component without harness connected
    (Front Power Window Regulator Motor Assembly LH)
    *b
    Clockwise
    *c
    Counterclockwise


INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on Driver Door Window Only)

  1. B295578E01
    Check the operation of the regulator motor.

  1. Apply battery voltage to the regulator motor and check the operation of the regulator motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1
    Motor gear rotates counterclockwise

    1. If the result is not as specified, replace the regulator motor assembly.
      Text in Illustration 
      *1
      Motor Gear
      *a
      Component without harness connected
      (Front Power Window Regulator Motor Assembly RH)
      *b
      Clockwise
      *c
      Counterclockwise

← REMOVAL (from Jan 2012)INSTALLATION (Sep 2011 – Dec 2011) →