2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 "TORX" driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.


2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B180924E04
    Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.

  1. Loosely install the temporary bolt onto the window regulator.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

    NOTICE:
    Be careful not to drop the window regulator as it may become damaged.

  1. Temporarily install the window regulator with the 3 bolts.

  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

  1. B180922
    Slide the rear door glass sub-assembly as shown in the illustration to install it.


4. INSTALL REAR DOOR QUARTER WINDOW GLASS

  1. B183926
    Install the quarter glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


5. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

  1. B180920
    Install the rear door rear lower window frame with the 2 bolts and screw.


6. INSTALL REAR DOOR GLASS RUN

  1. B180919
    Install the rear door glass run.


7. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the door.

  1. B180918
    Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

    NOTICE:
    1. When installing the service hole cover, pull the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. B183933E02
    Connect the 2 connectors.

  1. Attach the 6 clamps.

  1. B180916E01
    Install the bolt as shown in the illustration.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


8. INSTALL REAR SPEAKER SET (w/ Rear Speaker)

  1. B181520
    Temporarily install the speaker by attaching the claw of the speaker to the door panel.

  1. Install the speaker with the 3 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.


9. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP

  1. B180917E02
    Install the rear inner door glass weatherstrip to the door panel.


10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.

  1. B183925
    Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

  1. B180912
    Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly.

  1. Install the 3 screws.


11. INSTALL ASSIST GRIP COVER

  1. B183924
    Attach the 9 claws to install the door assist grip cover to the door trim panel.


12. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY
  1. Connect the connector.

  1. B183923
    Attach the 7 claws to install the armrest base panel.


13. INSTALL REAR DOOR INSIDE HANDLE BEZEL

  1. B183922
    Attach the 4 claws to install the bezel.


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSPECTION (from Sep 2011)INSTALLATION (from Jan 2012) →