2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 "TORX" driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new rear window regulator motor uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.


2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B180924E04
    Apply MP grease to the sliding parts of the rear door window regulator sub-assembly LH.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Loosely install the temporary bolt onto the rear door window regulator sub-assembly LH.

  1. Insert the rear door window regulator sub-assembly LH into the door panel. Use the temporary bolt to hang the rear door window regulator sub-assembly LH on the door panel.

    NOTICE:
    Be careful not to drop the rear door window regulator sub-assembly LH as it may become damaged.

  1. Temporarily install the rear door window regulator sub-assembly LH with the 3 bolts.

  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

  1. B180922
    Slide the rear door glass sub-assembly LH as shown in the illustration to install it.


4. INSTALL REAR DOOR QUARTER WINDOW GLASS

  1. B183926
    Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.


5. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
  1. Install the rear door rear lower window frame sub-assembly LH with the 2 bolts and screw.


6. INSTALL REAR DOOR GLASS RUN
  1. Install the rear door glass run LH.


7. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the door.

  1. B180918
    Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

    NOTICE:
    1. When installing the rear door service hole cover LH, pull the links and connectors through the rear door service hole cover LH.
    2. There should be no wrinkles or folds after attaching the rear door service hole cover LH.
    3. After attaching the rear door service hole cover LH, check the sealing quality.

  1. Connect the 2 connectors.

  1. Attach the 6 clamps.

  1. B180916E01
    Install the bolt as shown in the illustration.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


8. INSTALL REAR SPEAKER SET (w/ Rear Speaker)

  1. B181520
    Temporarily install the speaker by attaching the claw of the speaker to the door panel.

  1. Install the speaker with the 3 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.


9. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP

  1. B180917E02
    Install the rear inner door glass weatherstrip LH to the door panel.


10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.

  1. B183925
    Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH to the rear door inside handle sub-assembly LH.

  1. B180912
    Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly LH.

  1. Install the 3 screws.


11. INSTALL ASSIST GRIP COVER
  1. Attach the 9 claws to install the assist grip cover LH to the rear door trim board sub-assembly LH.


12. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY
  1. Connect the connector.

  1. B183923
    Attach the 7 claws to install the armrest base panel.


13. INSTALL REAR DOOR INSIDE HANDLE BEZEL
  1. Install the rear door inside handle bezel LH to the trim board with the 6 screws.


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →