2011-2013 Land Cruiser · Service Manual Vehicle Interior

B279A Theft Deterrent System Communication Line High Fixation

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If the communication line (EFIO-IMI) to the ID code box (immobiliser code ECU) is stuck on HI output, the ECM outputs this DTC.
DTC Code
DTC Detection Condition
Trouble Area
B279A
When the communication line (EFIO-IMI) between the ECM and the ID code box (immobiliser code ECU) is stuck on HI output.
  1. Harness or connector
  2. ID code box (immobiliser code ECU)
  3. ECM

WIRING DIAGRAM

B192183E06
B192183E05
B262568E01

INSPECTION PROCEDURE


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    If DTCs other than DTC B279A are output, troubleshoot those DTCs first.

    Result 
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B



B
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3. CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

  1. B192185E23
    Disconnect the E28 ID code box connector.

  1. B192185E24
    Disconnect the A38*1 or A52*2 ECU connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance and voltage according to the value(s) in the table below.

    1. for 1UR-FE

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E28-6 (EFIO) - A38*1-40 (IMI)
      Always
      Below 1 Ω
      E28-6 (EFIO) or A38*1-40 (IMI) - Body ground
      Always
      10 kΩ or higher
      E28-6 (EFIO) - A52*2-40 (IMI)
      Always
      Below 1 Ω
      E28-6 (EFIO) or A52*2-40 (IMI) - Body ground
      Always
      10 kΩ or higher

      HINT:
      1. *1: for LHD
      2. *2: for RHD

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      E28-6 (EFIO) - Body ground
      Always
      Below 1 V
      A38*1-40 (IMI) - Body ground
      A52*2-40 (IMI) - Body ground

      HINT:
      1. *1: for LHD
      2. *2: for RHD

    2. for 1GR-FE, 1VD-FTV

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E28-6 (EFIO) - A38*1-11 (IMI)
      Always
      Below 1 Ω
      E28-6 (EFIO) or A38*1-11 (IMI) - Body ground
      Always
      10 kΩ or higher
      E28-6 (EFIO) - A52*2-11 (IMI)
      Always
      Below 1 Ω
      E28-6 (EFIO) or A52*2-11 (IMI) - Body ground
      Always
      10 kΩ or higher

      HINT:
      1. *1: for LHD
      2. *2: for RHD

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      E28-6 (EFIO) - Body ground
      Always
      Below 1 V
      A38*1-11 (IMI) - Body ground
      A52*2-11 (IMI) - Body ground

      HINT:
      1. *1: for LHD
      2. *2: for RHD

    3. for 3UR-FE

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E28-6 (EFIO) - A38-40 (IMI)
      Always
      Below 1 Ω
      E28-6 (EFIO) or A38-40 (IMI) - Body ground
      Always
      10 kΩ or higher

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      E28-6 (EFIO) - Body ground
      Always
      Below 1 V
      A38-40 (IMI) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK ID CODE BOX (IMMOBILISER CODE ECU) (OUTPUT)
B178967E01
  1. Using an oscilloscope, check the waveform.

    Measurement Condition 
    Item
    Content
    Tester Connection
    E28-6 (EFIO) - E28-8 (GND)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Engine switch on (IG)

    OK:
    Waveform is output normally (see illustration).

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1GR-FE)
    B
    OK (for 1UR-FE)
    C
    OK (for 1VD-FTV)
    D
    OK (for 3UR-FE)
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPLACE ECM (Click here)
A


5. CHECK ID CODE BOX (IMMOBILISER CODE ECU) (POWER SOURCE AND BODY GROUND)
B164101E04
  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connector
    Condition
    Specified Condition
    E28-1 (+B) - E28-8 (GND)
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


← B279A Theft Deterrent System Communication Line High Fixation (Sep 2011 – Dec 2011)B279C Theft Deterrent System Presence Detection (Sep 2011 – Dec 2011) →