Rear Door RH Entry Unlock Function does not Operate
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
If the rear door RH entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be a touch sensor circuit (certification ECU (smart key ECU assembly) → rear door outside handle RH → rear door electrical key oscillator RH).- HINT:
- For vehicles with entry function for rear doors.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK POWER DOOR LOCK OPERATION |
When the master switch assembly door control switch is operated, check that the locked doors unlock.
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
for LHD
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
PR Door Lock Position SW
Passenger side rear door lock position switch signal / ON or OFF
ON: Passenger side rear door unlocked
OFF: Passenger side rear door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
for RHD
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
DR Door Lock Position SW
Driver side rear door lock position switch signal / ON or OFF
ON: Driver side rear door unlocked
OFF: Driver side rear door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR) |
Using the intelligent tester, read the Data List.
for LHD
Entry & Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Pr-Door Touch Sensor
Passenger side rear door touch sensor / ON or OFF
ON: Touch sensor touched
OFF: Touch sensor not touched
-
- OK:
- "ON" (sensor is touched) and "OFF" (sensor is not touched) appears on the screen.
for RHD
Entry & Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Dr-Door Touch Sensor
Driver side rear door touch sensor / ON or OFF
ON: Touch sensor touched
OFF: Touch sensor not touched
-
- OK:
- "ON" (sensor is touched) and "OFF" (sensor is not touched) appears on the screen.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the E30 ECU connector.

Disconnect the z26 oscillator connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
E30-2 (SEL4) - z26-4 (SEL)
Always
Below 1 Ω
E30-27 (SEN4) - z26-6 (SENS)
Always
Below 1 Ω
E30-2 (SEL4) - Body ground
Always
10 kΩ or higher
E30-27 (SEN4) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
E30-1 (SEL3) - z26-4 (SEL)
Always
Below 1 Ω
E30-28 (SEN3) - z26-6 (SENS)
Always
Below 1 Ω
E30-1 (SEL3) - Body ground
Always
10 kΩ or higher
E30-28 (SEN3) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE) |
Disconnect the z25 handle connector.

Disconnect the z26 oscillator connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z25-6 (SGT) - z26-2 (SGT)
Always
Below 1 Ω
z25-6 (SGT) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator (Click here).
| NEXT | |
| 7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry function operates normally.
- OK:
- Operates normally.
|
|
||||
| OK | ||
| ||
| 8. REPLACE REAR DOOR OUTSIDE HANDLE |
Replace the rear door outside handle (Click here).
| NEXT | |
| 9. CHECK REAR DOOR OUTSIDE HANDLE (OPERATION) |
Check that the entry function operates normally.
- OK:
- Operates normally.
|
|
||||
| OK | ||
| ||
