TERMINALS OF ECU
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |


Disconnect the E1, E2, E3, 2A, 2B, 2C, and 2D ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2A-1 (ACC) - Body ground
B - Body ground
ACC power supply
Always
11 to 14 V
2A-1 (IG) - Body ground
B - Body ground
IG power supply
Always
11 to 14 V
2A-1 (TRLY) - Body ground
B - Body ground
Taillight power supply
Always
11 to 14 V
2D-62 (GND2) - Body ground
W-B - Body ground
Body ground
Always
Below 1 Ω
2D-62 (GND1) - Body ground*1
W-B - Body ground
Body ground
Always
Below 1 Ω
E3-1 (GND3) - Body ground
BR - Body ground
Body ground
Always
Below 1 Ω
E1-24 (DCTY) - Body ground*2
L - Body ground
Front door courtesy light switch LH signal
Front door LH open
Below 1 Ω
E1-24 (DCTY) - Body ground*2
L - Body ground
Front door courtesy light switch LH signal
Front door LH closed
10 kΩ or higher
E1-24 (DCTY) - Body ground*3
Y - Body ground
Front door courtesy light switch LH signal
Front door LH open
Below 1 Ω
E1-24 (DCTY) - Body ground*3
Y - Body ground
Front door courtesy light switch LH signal
Front door LH closed
10 kΩ or higher
E2-21 (PCTY) - Body ground*2
Y - Body ground
Front door courtesy light switch RH signal
Front door RH open
Below 1 Ω
E2-21 (PCTY) - Body ground*2
Y - Body ground
Front door courtesy light switch RH signal
Front door RH closed
10 kΩ or higher
E2-21 (PCTY) - Body ground*3
L - Body ground
Front door courtesy light switch RH signal
Front door RH open
Below 1 Ω
E2-21 (PCTY) - Body ground*3
L - Body ground
Front door courtesy light switch RH signal
Front door RH closed
10 kΩ or higher
2C-2 (LCTY) - Body ground
W - Body ground
Rear door courtesy light switch LH signal
Rear door LH open
Below 1 Ω
2C-2 (LCTY) - Body ground
W - Body ground
Rear door courtesy light switch LH signal
Rear door LH closed
10 kΩ or higher
E2-7 (RCTY) - Body ground*4
G - Body ground
Rear door courtesy light switch RH signal
Rear door RH open
Below 1 Ω
E2-7 (RCTY) - Body ground*4
G - Body ground
Rear door courtesy light switch RH signal
Rear door RH closed
10 kΩ or higher
E1-17 (RCTY) - Body ground*1
G - Body ground
Rear door courtesy light switch RH signal
Rear door RH open
Below 1 Ω
E1-17 (RCTY) - Body ground*1
G - Body ground
Rear door courtesy light switch RH signal
Rear door RH closed
10 kΩ or higher
E2-25 (BCTY) - Body ground
W - Body ground
Back door courtesy light switch signal
Back door open
Below 1 Ω
E2-25 (BCTY) - Body ground
W - Body ground
Back door courtesy light switch signal
Back door closed
10 kΩ or higher
E1-23 (TAIL) - Body ground
V - Body ground
Light control switch TAIL signal
Light control switch tail
Below 1 Ω
E1-23 (TAIL) - Body ground
V - Body ground
Light control switch TAIL signal
Light control switch except tail
10 kΩ or higher
E2-17 (HEAD) - Body ground
R- Body ground
Light control switch HEAD signal
Light control switch head
Below 1 Ω
E2-17 (HEAD) - Body ground
R - Body ground
Light control switch HEAD signal
Light control switch except head
10 kΩ or higher
E1-21 (A) - Body ground
G - Body ground
Light control switch AUTO signal
Light control switch auto
Below 1 Ω
E1-21 (A) - Body ground
G - Body ground
Light control switch AUTO signal
Light control switch except auto
10 kΩ or higher
E2-28 (FFOG) - Body ground
R - Body ground
Front fog light switch signal
Front fog light switch on
Below 1 Ω
E2-28 (FFOG) - Body ground
R - Body ground
Front fog light switch signal
Front fog light switch off
10 kΩ or higher
E2-9 (RFOG) - Body ground
R - Body ground
Rear fog light switch signal
Rear fog light switch on
Below 1 Ω
E2-9 (RFOG) - Body ground
R - Body ground
Rear fog light switch signal
Rear fog light switch off
10 kΩ or higher
2D-13 (HU) - Body ground
R - Body ground
Dimmer switch high signal
Dimmer switch high
Below 1 Ω
2D-13 (HU) - Body ground
R - Body ground
Dimmer switch high signal
Dimmer switch except high or flash
10 kΩ or higher
E1-13 (HF) - Body ground
GR - Body ground
Dimmer switch flash signal
Dimmer switch flash
Below 1 Ω
E1-13 (HF) - Body ground
GR - Body ground
Dimmer switch flash signal
Dimmer switch except flash
10 kΩ or higher
2D-51 (ILE) - Body ground
G - Body ground
Interior light signal
Map light on
Below 1 Ω
2D-51 (ILE) - Body ground
G - Body ground
Interior light signal
Map light off
10 kΩ or higher
- HINT:
- *1: w/o Entry and Start System
- *2: for LHD
- *3: for RHD
- *4: w/ Entry and Start System
Reconnect the E1, E2, E3, 2A, 2B, 2C, and 2D ECU connectors.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E1-4 (FFGO) - Body ground
R - Body ground
Front fog light signal
Light control switch tail,
front fog light switch on
Below 1 V
E1-4 (FFGO) - Body ground
R - Body ground
Front fog light signal
Light control switch tail,
front fog light switch off
11 to 14 V
E2-8 (DRLE) - Body ground
R - Body ground
Daytime running light signal
Daytime running light on
Below 1 V
E2-8 (DRLE) - Body ground
R - Body ground
Daytime running light signal
Daytime running light off
11 to 14 V
E3-14 (RFGO) - Body ground
R - Body ground
Rear fog light signal
Light control switch tail,
rear fog light switch off
Below 1 V
E3-14 (RFGO) - Body ground
R - Body ground
Rear fog light signal
Light control switch tail,
rear fog light switch off
11 to 14 V
2B-18 (HRLY) - Body ground
L - Body ground
Headlight low beam signal
Light control switch head,
dimmer switch low
Below 1 V
2B-18 (HRLY) - Body ground
L - Body ground
Headlight low beam signal
Light control switch head,
dimmer switch except low
11 to 14 V
2B-16 (DIM) - Body ground
R-G - Body ground
Headlight low beam signal
Light control switch head,
dimmer switch high
Below 1 V
2B-16 (DIM) - Body ground
R-G - Body ground
Headlight low beam signal
Light control switch head,
dimmer switch except high
11 to 14 V
2B-22 (STP) - Body ground
R - Body ground
Stop light switch signal
Brake pedal depressed
11 to 14 V
2B-22 (STP) - Body ground
R - Body ground
Stop light switch signal
Brake pedal released
Below 1 V
| CHECK HEADLIGHT LEVELING ECU ASSEMBLY (w/ Static Headlight Auto Leveling) |


Disconnect the E109 headlight leveling ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E109-1 (IG) - Body ground
R - Body ground
Ignition power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
E109-9 (E1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the E109 headlight leveling ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E109-3 (HDLP) - E109-9 (E1)
L - W-B
Low beam headlight signal input
Low beam headlights on
Below 1 V
Low beam headlights off
11 to 14 V
E109-5 (INIT) - E109-9 (E1)
LG - W-B
Initialization signal input
Terminal LVL and terminal CG of DLC3 connected
Below 1 V
Terminal LVL and terminal CG of DLC3 not connected
4.5 to 5.5 V
E109-6 (WNG) - E109-9 (E1)
L - W-B
Warning indicator drive output
Warning indicator on
Below 1 V
Warning indicator off
11 to 14 V
E109-10 (RH+) - E109-9 (E1)
G - W-B
Headlight leveling motor RH power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
E109-11 (LH+) - E109-9 (E1)
R - W-B
Headlight leveling motor LH power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
E109-12 (SBR) - E109-21 (SGR)
L - P
Rear height control sensor power supply
Ignition switch off
Below 1 V
Ignition switch ON
4.75 to 5.25 V
E109-16 (SPDR) - E109-9 (E1)
V - W-B
Vehicle speed signal input
Vehicle is driven at approximately 20 km/h (12 mph)
Pulse generation
(See waveform 1)
E109-17 (RHT) - E109-9 (E1)
P - W-B
Headlight leveling motor RH operation signal input
With low beam headlights on, vehicle height not changed
Below 1 V
With low beam headlights on, vehicle height changed and maintained for more than 3 seconds
1.0 to 14.4 V
E109-18 (LHT) - E109-9 (E1)
G - W-B
Headlight leveling motor LH operation signal input
With low beam headlights on, vehicle height not changed
Below 1 V
With low beam headlights on, vehicle height changed and maintained for more than 3 seconds
1.0 to 14.4 V
E109-19 (SHRL) - E109-21 (SGR)
Y - P
Rear height control sensor signal input
Ignition switch off
Below 1 V
Ignition switch ON
0.5 to 4.5 V
E109-21 (SGR) - E109-9 (E1)
P - W-B
Rear height control sensor ground
Always
Below 1 Ω
E109-23 (RH-) - E109-9 (E1)
BR - W-B
Headlight leveling motor RH ground
Always
Below 1 Ω
E109-24 (LH-) - E109-9 (E1)
V - W-B
Headlight leveling motor LH ground
Always
Below 1 Ω
Waveform 1

Item
Content
Terminal No. (Symbol)
E109-16 (SPDR) - E109-9 (E1)
Tool setting
5 V/DIV., 20 ms./DIV.
Condition
Vehicle is driven at approximately 20 km/h (12 mph)
- HINT:
- When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (w/ Dynamic Headlight Auto Leveling) |


Disconnect the E101 headlight swivel ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E101-15 (IG) - Body ground
R - Body ground
Ignition power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
E101-22 (E1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the E101 headlight swivel ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E101-3 (LHT) - E101-22 (E1)
R - W-B
Headlight leveling motor LH power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
E101-4 (RHT) - E101-22 (E1)
G - W-B
Headlight leveling motor RH power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
E101-7 (INIT) - E101-22 (E1)
LG - W-B
Initialization signal
Ignition switch ON, terminals LVL and GND of DLC3 connected
Below 1 V
Ignition switch ON, terminals LVL and GND of DLC3 not connected
4.5 to 5.5 V
E101-11 (RH+) - E101-22 (E1)
P - W-B
Headlight leveling motor RH LIN communication
Ignition switch off
Below 1 V
Ignition switch ON
Pulse generation
E101-17 (SHFL) - E101-22 (E1)*1
GR - W-B
Vehicle height signal
Ignition switch off
Below 1 V
Ignition switch ON
Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
E101-18 (SBR) - E101-22 (E1)*1
L - W-B
Vehicle height signal
Ignition switch off
Below 1 V
Ignition switch ON
4.5 to 5.5 V
E101-18 (SBR) - E101-21 (SGR)*2
L - P
Rear height control sensor LH power supply
Ignition switch off
Below 1 V
Ignition switch ON
4.5 to 5.5 V
E101-19 (SHRL) - E101-22 (E1)*1
Y - W-B
Vehicle height signal
Ignition switch off
Below 1 V
Ignition switch ON
Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
E101-19 (SHRL) - E101-21 (SGR)*2
Y - P
Rear height control sensor LH signal
Ignition switch off
Below 1 V
Ignition switch ON
Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
E101-21 (SGR) - E101-22 (E1)*1
P - W-B
Vehicle height signal
Always
Below 1 Ω
E101-21 (SGR) - E101-22 (E1)*2
P - W-B
Rear height control sensor LH ground
Always
Below 1 Ω
E101-27 (LH-) - E101-22 (E1)
V - W-B
Headlight leveling motor LH ground
Always
Below 1 Ω
E101-28 (RH-) - E101-22 (E1)
BR - W-B
Headlight leveling motor RH ground
Always
Below 1 Ω
E101-30 (LH+) - E101-22 (E1)
G - W-B
Headlight leveling motor LH LIN communication
Ignition switch off
Below 1 V
Ignition switch ON
Pulse generation
- *1: w/ Active Height Control Suspension
- *2: w/o Active Height Control Suspension
- *1: w/ Active Height Control Suspension