2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. REMOVE FRONT FENDER APRON SEAL LH

  1. A176301
    Using a clip remover, remove the 4 clips and fender apron seal.


2. REMOVE FRONT FENDER APRON SEAL LH (w/ KDSS)

  1. A177004
    Using a clip remover, remove the 3 clips and fender apron seal.


3. REMOVE FRONT FENDER APRON SEAL REAR LH

  1. A177005
    Using a clip remover, remove the 4 clips and fender apron seal.


4. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Using a clip remover, remove the 3 clips and fender apron seal.


5. REMOVE FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Using a clip remover, remove the 4 clips and fender apron seal.


6. DISCONNECT COOLER COMPRESSOR

  1. A180811
    Disconnect the connector.

  1. Remove the bolt. Then disconnect the cooler refrigerant suction hose from the cylinder head cover.

  1. Remove the 3 bolts, nut and No. 1 compressor stay and disconnect the cooler compressor.


7. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A178868E01
    Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


8. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


9. REMOVE TAILPIPE ASSEMBLY
  1. Remove the bolt, clamp and gasket.

  1. Remove the tailpipe from the 2 exhaust pipe supports.


10. REMOVE CENTER EXHAUST PIPE ASSEMBLY
  1. Remove the 4 bolts.

  1. Remove the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the 2 gaskets from the front exhaust pipe and front No. 2 exhaust pipe.


11. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Detach the heated oxygen sensor wire clamp.

  1. Remove the 3 nuts, front exhaust pipe and gasket.


12. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 3 nuts, front No. 2 exhaust pipe and gasket.


13. REMOVE NO. 1 MANIFOLD STAY

  1. A175111
    Remove the 3 bolts and manifold stay.


14. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A167926
    Remove the 4 bolts and heat insulator.


15. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A167927
    Remove the 8 nuts and exhaust manifold.

  1. A176362E01
    Remove the gasket from the cylinder head RH.


16. REMOVE NO. 2 MANIFOLD STAY

  1. A175112
    Remove the 3 bolts and manifold stay.


17. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A167928
    Remove the 4 bolts and heat insulator.


18. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A167929
    Remove the 8 nuts and exhaust manifold.

  1. A176363E01
    Remove the gasket from the cylinder head LH.

← COMPONENTS (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →