2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE OIL PRESSURE SENSOR
  1. Using a 24 mm deep socket wrench, remove the oil pressure sensor.


2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Remove the engine coolant temperature sensor and gasket.


3. DISCONNECT NO. 1 WATER BY-PASS PIPE (for Automatic Transmission)

  1. A177655
    Disconnect the 2 water by-pass pipe hoses and remove the pipe.


4. DISCONNECT WATER HOSE SUB-ASSEMBLY (for Automatic Transmission)

  1. A179580
    Remove the 2 bolts and disconnect the water hose.


5. DISCONNECT WATER HOSE SUB-ASSEMBLY (for Manual Transmission)

  1. A179581E01
    Remove the 2 bolts and disconnect the water hose.


6. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A133704
    Disconnect the 6 fuel injector connectors.

  1. Remove the 6 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.


7. REMOVE FUEL INJECTOR

  1. A133705E01
    Pull the 6 fuel injectors from the fuel delivery pipe.

  1. Remove the O-ring and injector vibration insulator from each fuel injector.


8. REMOVE INTAKE MANIFOLD

  1. A151776
    Remove the 10 bolts, intake manifold and 2 gaskets.


9. REMOVE ENGINE WIRE

A174353E01

10. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 6 bolts and 6 ignition coils.


11. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A175285
    Remove the 5 bolts and V-ribbed belt tensioner.


12. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A175286
    Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


13. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A175287
    Remove the 4 bolts and front No. 1 engine mounting bracket RH.


14. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A175288
    Remove the 3 bolts and front No. 1 engine mounting bracket LH.


15. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A239030
    Remove the bolt and No. 1 idler pulley.


16. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A191314E01
    w/ Pulley Cover Plate:
    Remove the 2 bolts, 2 No. 2 idler pulley cover plate, 2 idler pulley and 2 idler pulley cover plate.

  1. A076338E01
    w/o Pulley Cover Plate:
    Remove the 2 bolts and 2 No. 2 idler pulleys.


17. REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

HINT:
If the flywheel ring gear is deformed or the gears are damaged, replace it.

CAUTION:
Wear protective gloves. Hot ares on the flywheel ring gear may injure your hands.

  1. A177669E01
    Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

  1. Temporarily install 6 bolts (8 mm x 1.25 pitch) with a length of 70 mm or more to the flywheel.

  1. Uniformly tighten the 6 bolts in the order shown in the illustration.

  1. Remove the ring gear from the flywheel.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →