2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE ENGINE WIRE

2. DISCONNECT HEATER WATER HOSE ASSEMBLY

  1. A271020E01
    Remove the 2 bolts and disconnect the 2 water hoses.
    Text in Illustration 
    *A
    w/o ATF Warmer
    *B
    w/ ATF Warmer


3. REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A267738
    Disconnect the No. 1 emission control valve set connector.

  1. Disconnect the No. 1 air hose from the No. 1 emission control valve set.

  1. A223570
    Remove the 3 nuts and No. 1 emission control valve set.


4. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A223562
    Disconnect the No. 2 emission control valve set connector.

  1. Disconnect the No. 3 air hose.

  1. A223564
    Remove the 3 nuts and No. 2 emission control valve set.


5. REMOVE IGNITION COIL ASSEMBLY

  1. A272605E01
    Disconnect the 6 ignition coil connectors.
    Text in Illustration 
    *A
    Bank 1
    *B
    Bank 2

  1. Remove the 6 bolts and 6 ignition coils.


6. REMOVE FUEL PIPE SUB-ASSEMBLY

  1. A224750
    Disconnect the 2 fuel pipes (Click here).

  1. Remove the 2 bolts and No. 1 and No. 2 fuel pipes.


7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A223037
    Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.


8. REMOVE FUEL INJECTOR ASSEMBLY

  1. A223038E01
    Remove the 6 fuel injectors from the fuel delivery pipe.
    Text in Illustration 
    *1
    Fuel Delivery Pipe
    *2
    Fuel Injector

  1. Remove the O-ring and injector vibration insulator from each fuel injector.


9. REMOVE INTAKE MANIFOLD

  1. A271403
    Remove the 4 nuts, 6 bolts and 2 gaskets.


10. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A223013
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


11. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A158544
    Remove the bolt and No. 1 idler pulley.


12. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A223006
    Remove the 2 bolts and 2 No. 2 idler pulleys.


13. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A222180
    Remove the 5 bolts and V-ribbed belt tensioner.


14. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A270151
    Remove the engine oil level dipstick.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.


15. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A221156
    Remove the 3 bolts and front No. 1 engine mounting bracket LH.


16. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A221155
    Remove the 4 bolts and front No. 1 engine mounting bracket RH.


17. REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

HINT:
If the flywheel ring gear is deformed or the gears are damaged, replace it.

CAUTION:
Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.

  1. A177669E01
    Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

  1. Temporarily install 6 bolts (8 mm (0.315 in.) x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel.

  1. Uniformly tighten the 6 bolts in the order shown in the illustration.

  1. Remove the ring gear from the flywheel.

← REMOVAL (Sep 2011 – Dec 2011)DISASSEMBLY (Sep 2011 – Dec 2011) →