INSTALLATION
Removal / installation · Vehicles built from Sep 2011
| 1. INSTALL 4 WHEEL DRIVE CONTROL ECU NO.2 |
Install the ECU with the bolt.

- Torque:
- 13 N*m{ 127 kgf*cm , 9 ft.*lbf }
Connect the 2 ECU connectors.
| 2. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for RHD) |
Connect the connector.

- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Install the driver side knee airbag with the 5 bolts.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 3. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for RHD) |
Connect the connectors.
for Automatic Air Conditioning System:

Attach the 2 claws to install the room temperature sensor.
Attach the 2 claws to connect the 2 control cables.

w/ Driver Side Knee Airbag:
Attach the 16 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.


w/o Driver Side Knee Airbag:
Attach the 9 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.


Attach the 2 claws to close the hole cover.

| 4. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD) |
w/ Floor Under Cover:
Install the No. 1 instrument panel under cover (Click here).
| 5. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD) |
Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.


Text in Illustration *A
w/ Entry and Start System
*B
w/o Entry and Start System
| 6. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD) |
![]() ![]() |
Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.
| 7. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH (for RHD) |
Attach the 7 claws to install the panel pad.

Install the screw.
Install the clip.
| 8. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for RHD) |
Connect the connectors.
for Automatic Air Conditioning System:

Attach the 2 claws to install the room temperature sensor.
Attach the 2 claws to connect the 2 control cables.

w/ Driver Side Knee Airbag:
Attach the 16 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.


w/o Driver Side Knee Airbag:
Attach the 9 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.


Attach the 2 claws to close the hole cover.

| 9. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for LHD) |
![]() ![]() |
Connect the connector.
Attach the 3 claws to install the lower No. 2 instrument panel finish panel.
Install the 4 bolts.
| 10. INSTALL INSTRUMENT PANEL BOX DOOR KNOB (for LHD) |
![]() ![]() |
Attach the 2 claws to install the instrument panel box door knob.
| 11. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD) |
![]() ![]() |
Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.
| 12. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (for LHD) |
Connect the connector.

- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Attach the 4 claws to install the front passenger side knee airbag.
Install the 4 bolts.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 13. INSTALL COWL SIDE TRIM BOARD RH |
![]() ![]() |
Attach the 2 clips to install the cowl side trim board.
Install the cap nut.
| 14. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD) |
w/ Floor Under Cover:
Install the No. 2 instrument panel under cover (Click here).
| 15. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.





