2011-2013 Land Cruiser · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built from Sep 2011


1. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


2. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
  1. w/ Floor Under Cover:

    1. Remove the No. 2 instrument panel under cover (Click here).


3. REMOVE COWL SIDE TRIM BOARD RH

B180022
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


4. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (for LHD)

  1. B189606E01
    Remove the 4 bolts.

  1. Detach the 4 claws and remove the front passenger side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


5. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)

B180303E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.


6. REMOVE INSTRUMENT PANEL BOX DOOR KNOB (for LHD)

B182302
  1. Using a moulding remover, detach the 2 claws and remove the instrument panel box door knob.


7. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for LHD)

B180304
  1. Remove the 4 bolts.

  1. Detach the 3 claws.

  1. Disconnect the connector and remove the lower No. 2 instrument panel finish panel.


8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for RHD)

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


9. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH (for RHD)

  1. B180005
    Remove the clip.

  1. Remove the screw.

  1. Detach the 7 claws and remove the panel.


10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD)

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


11. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD)
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


12. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
  1. w/ Floor Under Cover:

    1. Remove the No. 1 instrument panel under cover (Click here).


13. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for RHD)

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


14. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (for RHD)

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


15. REMOVE 4 WHEEL DRIVE CONTROL ECU NO.2

  1. C172064
    Disconnect the 2 ECU connectors.

  1. Remove the bolt and ECU.

← COMPONENTS (from Sep 2011)INSTALLATION (from Sep 2011) →