2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSPECTION

Inspection · Vehicles built from Sep 2011


INSPECT CYLINDER HEAD SET BOLT

  1. A122880E18
    Using a vernier caliper, measure the diameter of the elongated thread at the measuring point.

    Measuring point:
    94 mm (3.70 in.) for intake side bolt
    89 mm (3.50 in.) for exhaust side bolt

    Standard diameter:
    10.85 to 11.00 mm (0.427 to 0.433 in.)

    Minimum diameter:
    10.6 mm (0.417 in.)

    Text in Illustration 
    *1
    Measuring Point
    If the diameter is less than the minimum, replace the cylinder head bolt.

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the smallest diameter.


INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Turn the roller by hand to check that it turns smoothly.
    If the roller does not turn smoothly, replace the valve rocker arm.


INSPECT VALVE LASH ADJUSTER ASSEMBLY

A186391E03

NOTICE:
  1. Keep the adjuster free from dirt and foreign objects.
  2. Use only clean engine oil.

  1. Place the lash adjuster into a container full of new engine oil.

  1. Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

    SST
    09276-75010  

  1. Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    Text in Illustration 
    *1
    Taper Part
    *2
    Plunger
    *3
    Low Pressure Chamber
    *4
    Check Ball
    *5
    High Pressure Chamber
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

    OK:
    Plunger can be pressed 3 times.

    If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster with a new one.


INSPECT CAMSHAFT SUB-ASSEMBLY
  1. Inspect the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.04 mm (0.00157 in.)

      If the circle runout is more than the maximum, replace the camshaft sub-assembly.

      HINT:
      Check the oil clearance after replacing the camshaft.

  1. Using a micrometer, measure the cam lobe height.

    Standard Cam Lobe Height:
    Item
    Specified Condition
    Intake
    44.291 to 44.441 mm (1.744 to 1.750 in.)
    Exhaust
    44.196 to 44.346 mm (1.740 to 1.746 in.)

    Minimum Cam Lobe Height:
    Item
    Specified Condition
    Intake
    44.241 mm (1.742 in.)
    Exhaust
    44.146 mm (1.738 in.)

    If the cam lobe height is less than the minimum, replace the camshaft sub-assembly.

  1. Using a micrometer, measure the journal diameter.

    Standard Journal Diameter:
    Item
    Specified Condition
    No. 1 journal
    29.956 to 29.970 mm (1.179 to 1.180 in.)
    Other journals
    25.959 to 25.975 mm (1.022 to 1.023 in.)

    If the journal diameter is not as specified, check the oil clearance.


INSPECT CAMSHAFT OIL CLEARANCE
  1. Clean the bearing caps, camshaft housing and camshaft journals.

  1. Place the camshafts on the camshaft housing.

  1. A145569E06
    Lay a strip of Plastigage across each of the camshaft journals.
    Text in Illustration 
    *1
    Plastigage

  1. Install the camshaft bearing caps (Click here).

    NOTICE:
    Do not turn the camshaft.

  1. Install the camshaft housing (Click here).

    NOTICE:
    Do not turn the camshaft.

  1. Remove the camshaft bearing caps (Click here).

  1. A160675E04
    Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    No. 1 journal
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)
    Other journals
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    No. 1 journal
    0.10 mm (0.00394 in.)
    Other journals
    0.09 mm (0.00354 in.)

    Text in Illustration 
    *1
    Plastigage
    *2
    No. 1 Journal
    *3
    Other Journals
    If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.


INSPECT CAMSHAFT TIMING GEAR
  1. Install the camshaft bearing caps (Click here).

    HINT:
    Only install the intake camshaft.

  1. Install the camshaft housing (Click here).

  1. Apply a light coat of engine oil to the camshaft and camshaft timing gear.

  1. A160670E07
    Using the hexagonal portion of the camshaft, align and attach the knock pin of the camshaft with the pin hole of the camshaft timing gear.
    Text in Illustration 
    *1
    Knock Pin
    *2
    Key Groove

    NOTICE:
    1. Do not forcefully push on the camshaft timing gear. This may cause the camshaft knock pin tip to damage the installation surface of the camshaft timing gear.

    2. A160671E11
      Do not loosen or remove the 3 bolts shown in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the camshaft timing gear assembly with a new one.

    Text in Illustration 
    *1
    Flange Bolt
    *2
    Knock Pin
    *a
    Do not remove

  1. Apply a light coat of engine oil to the threads and under the head of the bolt.

  1. A164349E02
    Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing gear with the bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. Remove the camshaft bearing caps (Click here).

  1. Check the lock of the camshaft timing gear.

    1. Make sure that the camshaft timing gear is locked.

      NOTICE:
      Be careful not to damage the camshaft.

  1. A160672E05
    Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

    2. Break through the tape of the advance side path and retard side path as shown in the illustration.

      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Open
      *4
      Close
      V100144
      Vinyl Tape

    3. A160673E04
      Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two broken paths.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      NOTICE:
      Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.

    4. A160674E03
      Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Decompress
      *4
      Hold Pressure

      HINT:
      This operation releases the lock pin for the most retarded position.

    5. When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Turn the camshaft timing gear within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

      NOTICE:
      Do not use air pressure to perform the smooth rotation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear is locked at the most retarded position.

  1. Install the camshaft bearing caps (Click here).

    HINT:
    Only install the intake camshaft.

  1. Install the camshaft housing (Click here).

  1. A164348E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. Remove the camshaft bearing caps (Click here).

  1. A160671E11
    Remove the flange bolt and camshaft timing gear.
    Text in Illustration 
    *1
    Flange Bolt
    *2
    Knock Pin
    *a
    Do not remove


INSPECT CAMSHAFT TIMING EXHAUST GEAR
  1. Install the camshaft bearing caps (Click here).

    HINT:
    Only install the exhaust camshaft.

  1. Install the camshaft housing (Click here).

  1. Apply a light coat of engine oil to the camshaft and camshaft timing exhaust gear.

  1. A148246E08
    Using the hexagonal portion of the camshaft, align and attach the knock pin of the camshaft with the pin hole of the camshaft timing exhaust gear.
    Text in Illustration 
    *1
    Key Groove
    *2
    Knock Pin

    NOTICE:
    1. Do not forcefully push on the camshaft timing exhaust gear. This may cause the camshaft knock pin tip to damage the installation surface of the camshaft timing exhaust gear.

    2. A148250E09
      Do not loosen or remove the 4 bolts shown in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the camshaft timing exhaust gear assembly with a new one.

    Text in Illustration 
    *1
    Flange Bolt
    *a
    Do not remove

  1. Apply a light coat of engine oil to the threads and under the head of the bolt.

  1. A164350E02
    Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing exhaust gear with the bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. Remove the camshaft bearing caps (Click here).

  1. Check the camshaft timing exhaust gear lock.

    1. Make sure that the camshaft timing exhaust gear is locked.

  1. A148247E07
    Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

    2. Break through the tape of the advance side path and retard side path as shown in the illustration.

      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Open
      *4
      Close
      V100144
      Vinyl Tape

    3. A148248E04
      Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two broken paths (the advance side path and the retard side path).
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      NOTICE:
      Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.

    4. A148249E05
      Check that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Decompress
      *4
      Hold Pressure

      HINT:
      The lock pin is released and the camshaft timing exhaust gear turns in the retard direction.

    5. When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

      NOTICE:
      Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear may abruptly shift in the advance direction and break the lock pin or other parts.

  1. Check for smooth rotation.

    1. Turn the camshaft timing exhaust gear within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.

      NOTICE:
      When the air pressure is released from the advance side path and then from the retard side path, the gear automatically returns to the most advanced position due to the advance assist spring operation, and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.

  1. Check the lock at the most advanced position.

    1. Make sure that the camshaft timing exhaust gear is locked at the most advanced position.

  1. Install the camshaft bearing caps (Click here).

    HINT:
    Only install the exhaust camshaft.

  1. Install the camshaft housing (Click here).

  1. A164351E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. Remove the camshaft bearing caps (Click here).

  1. A148250E09
    Remove the flange bolt and camshaft timing exhaust gear.
    Text in Illustration 
    *1
    Flange Bolt
    *a
    Do not remove


INSPECT NO. 1 CHAIN SUB-ASSEMBLY

A168044E16
  1. Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

  1. Using a vernier caliper, measure the length of 15 pins.

    Maximum chain elongation:
    136.9 mm (5.39 in.)

    Text in Illustration 
    *1
    Measuring Area

    HINT:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the No. 1 chain.


INSPECT NO. 2 CHAIN SUB-ASSEMBLY
  1. Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

  1. Using a vernier caliper, measure the length of 15 pins.

    Maximum chain elongation:
    137.6 mm (5.42 in.)

    HINT:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the No. 2 chain.


INSPECT CRANKSHAFT TIMING SPROCKET RH

A148252
  1. Wrap the chain around the sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    61.4 mm (2.42 in.)

    If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket RH.

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.


INSPECT CRANKSHAFT TIMING SPROCKET LH

A148252
  1. Wrap the chain around the sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    61.4 mm (2.42 in.)

    If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket LH.

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.


INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

A148251E05
  1. Move the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.

    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    If necessary, replace the No. 1 chain tensioner.


INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

A148258E06
  1. Check that the plunger moves smoothly.

  1. Measure the worn depth of the chain tensioner.

    Maximum depth:
    0.9 mm (0.0354 in.)

    Text in Illustration 
    *1
    Depth
    If the depth is more than the maximum, replace the No. 2 chain tensioner.


INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

A148259E06
  1. Check that the plunger moves smoothly.

  1. Measure the worn depth of the chain tensioner.

    Maximum depth:
    0.9 mm (0.0354 in.)

    Text in Illustration 
    *1
    Depth
    If the depth is more than the maximum, replace the No. 3 chain tensioner.


INSPECT NO. 1 CHAIN TENSIONER SLIPPER

  1. A148254E06
    for LH:
    Measure the worn depth of the chain tensioner slipper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *1
    Depth
    If the depth is more than the maximum, replace the No. 1 chain tensioner slipper.

  1. A148257E04
    for RH:
    Measure the worn depth of the chain tensioner slipper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *1
    Depth
    If the depth is more than the maximum, replace the No. 1 chain tensioner slipper.


INSPECT NO. 1 CHAIN VIBRATION DAMPER

  1. A178534E03
    for LH:
    Measure the worn depth of the chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *1
    Depth
    If the depth is more than the maximum, replace the No. 1 chain vibration damper.

  1. A148256E06
    for RH:
    Measure the worn depth of the chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *1
    Depth
    If the depth is more than the maximum, replace the No. 1 chain vibration damper.


INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY LH

A237029
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surface where the exhaust manifold LH contacts the cylinder head.

    Maximum warpage:
    0.7 mm (0.0276 in.)

    If the warpage is more than the maximum, replace the exhaust manifold LH.


INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY RH

A237030
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surface where the exhaust manifold RH contacts the cylinder head.

    Maximum warpage:
    0.7 mm (0.0276 in.)

    If the warpage is more than the maximum, replace the exhaust manifold RH.

← DISASSEMBLY (from Jan 2012)REASSEMBLY (Sep 2011 – Dec 2011) →