2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Sep 2011


1. REMOVE ENGINE WIRE

A237000
  1. Engine LH Side:

    1. Disconnect the 2 camshaft timing control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the 2 VVT sensor connectors.

    4. Disconnect the camshaft position sensor connector.

    5. Disconnect the vacuum switching valve connector (for ACIS).

    6. Disconnect the purge VSV connector.

    7. Disconnect the engine coolant temperature sensor connector.

    8. Disconnect the fuel injector connector.

    9. Disconnect the noise filter connector.

    10. Remove the bolt and disconnect the 7 clamps.

  1. A237001
    Engine RH Side:

    1. Disconnect the 2 camshaft timing control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the 2 VVT sensor connectors.

    4. Disconnect the fuel injector connector.

    5. Disconnect the noise filter connector.

    6. Disconnect the throttle sensor connector.

    7. Disconnect the oil pressure sender gauge connector.

    8. Disconnect the 9 clamps.

  1. A237002
    Engine Rear Side:

    1. Disconnect the sensor wire connector.

    2. Disconnect the 5 clamps.

    3. Remove the 3 bolts.

  1. Remove the engine wire.


2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A162089
    Remove the No. 1 engine cover sub-assembly.


3. REMOVE NO. 3 ENGINE COVER

  1. A237009
    Remove the No. 3 engine cover.


4. REMOVE NO. 1 FUEL HOSE

A237003
  1. Remove the fuel hose (Click here).


5. DISCONNECT NO. 2 FUEL TUBE

  1. A161418
    Disconnect the No. 2 fuel tube from the fuel pressure regulator (Click here).


6. DISCONNECT NO. 1 FUEL TUBE

  1. A217528E01
    Disconnect the No. 1 fuel tube from the fuel delivery pipe RH (for metallic type) (Click here).
    SST
    09268-21011  
    Text in Illustration 
    *A
    RH Side

  1. A161415E03
    LH Side:
    Disconnect the No. 1 fuel tube from the fuel delivery pipe LH (Click here).
    Text in Illustration 
    *A
    LH Side


7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH
  1. Disconnect the No. 7 wire harness connector.

  1. A161425
    Remove the 2 bolts and fuel delivery pipe LH.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head LH.


8. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH

  1. A161422
    Disconnect the ventilation hose and No. 6 wire harness connector.

  1. A161424
    Remove the 2 bolts and fuel delivery pipe RH.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head RH.


9. REMOVE FUEL INJECTOR ASSEMBLY

  1. A161427
    Remove the fuel injector from the fuel delivery pipe, and then disconnect the injector connector.

    NOTICE:
    A149189E06
    For reinstallation, attach a tag or label to the injector shaft.

  1. A149190E06
    Remove the O-ring from the fuel injector.
    Text in Illustration 
    *1
    O-Ring

  1. A174995E03
    Detach the 3 clamps and then remove the No. 6 wire harness from the delivery pipe RH.
    Text in Illustration 
    *A
    Fuel Delivery Pipe RH

  1. A174996E02
    Detach the 3 clamps and then remove the No. 7 wire harness from the delivery pipe LH.
    Text in Illustration 
    *A
    Fuel Delivery Pipe LH


10. REMOVE INTAKE MANIFOLD

  1. A178482
    Disconnect the ventilation hose from the ventilation pipe of the cylinder head cover LH and RH.

  1. A237004
    Disconnect the 2 water by-pass hoses.

  1. A184056
    Disconnect the No. 1 ventilation hose.

  1. A237005
    Remove the bolt and wire bracket from the intake manifold.

  1. A178483
    Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.


11. REMOVE NO. 2 FUEL TUBE

A237006
  1. Remove the 2 bolts and No. 2 fuel tube.


12. REMOVE NO. 1 FUEL TUBE

A237007

13. REMOVE NO. 2 ENGINE COVER

A237721

14. REMOVE NO. 1 ENGINE COVER

A237722

15. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A165547
    Remove the 3 bolts.

  1. Disconnect the 4 hoses and remove the water by-pass pipe.


16. REMOVE NO. 1 WATER BY-PASS HOSE

  1. A237017
    Remove the No. 1 water by-pass hose by disconnecting the hose from the water inlet housing and front water by-pass joint.


17. REMOVE FRONT WATER BY-PASS JOINT

  1. A162552
    Disconnect the No. 2 water by-pass hose from the water by-pass joint.

  1. Remove the 4 nuts, water by-pass joint and 2 gaskets.


18. REMOVE WATER INLET HOUSING

  1. A162554
    Remove the 3 bolts, water inlet housing and gasket.


19. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

A239167
  1. Remove the 2 bolts and water by-pass pipe.


20. REMOVE SENSOR WIRE

A174139
  1. Disconnect the 4 knock sensor connectors.

  1. Disconnect the 3 clamps. Then remove the sensor wire.


21. REMOVE SEPARATOR CASE

  1. A163108
    Remove the 4 bolts and separator case.


22. REMOVE KNOCK SENSOR

  1. A178478
    Remove the 4 bolts and 4 knock sensors.


23. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A163838E04
  1. Remove the 2 water drain cock plugs from the water drain cocks.

  1. Remove the 2 water drain cocks from the cylinder block.

    Text in Illustration 
    *A
    RH
    *B
    LH


24. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

A160649
  1. Remove the 4 bolts and mounting bracket.


25. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

A160648
  1. Remove the 4 bolts and mounting bracket.


26. REMOVE IGNITION COIL ASSEMBLY

  1. A178479
    Remove the 8 bolts and 8 ignition coils.


27. REMOVE NOISE FILTER
  1. Remove the 2 bolts and 2 noise filters from the cylinder head cover.

← COMPONENTS (from Jan 2012)DISASSEMBLY (Sep 2011 – Dec 2011) →