2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A163657
    Disconnect the sender gauge connector.

  1. A162467
    Remove the oil pressure sender gauge.


2. REMOVE OIL FILTER ELEMENT

  1. A094910E10
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A207196
    Remove the oil filter drain plug.

  1. A237032E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A207198
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A207199E02
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A209947E02
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


3. REMOVE NO. 1 OIL COOLER BRACKET

  1. A163672
    Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.


4. REMOVE OIL FILTER BRACKET

  1. A162469
    Remove the 2 bolts, 2 nuts and filter bracket.

  1. A162470
    Remove the 2 O-rings.


5. REMOVE OIL FILLER CAP SUB-ASSEMBLY

6. REMOVE OIL FILLER CAP HOUSING

  1. A161903
    Remove the 2 bolts, filler cap housing and gasket.


7. REMOVE SPARK PLUG
  1. Using a 16 mm plug wrench, remove the 8 spark plugs.


8. REMOVE VVT SENSOR

  1. A161904
    LH:
    Remove the 2 bolts and 2 VVT sensors.

  1. A161905
    RH:
    Remove the 2 bolts and 2 VVT sensors.


9. REMOVE CAMSHAFT POSITION SENSOR

  1. A161906
    Remove the bolt and camshaft position sensor.


10. REMOVE CRANK POSITION SENSOR PROTECTOR

A161907
  1. Remove the 2 bolts and sensor protector.


11. REMOVE CRANKSHAFT POSITION SENSOR

  1. A161908
    Remove the bolt and crankshaft position sensor.


12. REMOVE CAMSHAFT OIL CONTROL VALVE ASSEMBLY

  1. A161909
    LH:
    Remove the 2 bolts and 2 oil control valves.

  1. A161910
    RH:
    Remove the 2 bolts and 2 oil control valves.


13. REMOVE WATER PUMP PULLEY

  1. A151837E03
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.


14. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A162557
    Remove the bolt and idler pulley.


15. REMOVE FLUID COUPLING BRACKET

  1. A162558
    Remove the 4 bolts and fluid coupling bracket.


16. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A162527
    Remove the standard bolt, 6 mm hexagon wrench bolt and belt tensioner.


17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A162523
    Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A162524
    Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).


18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A163381
    Remove the bolt and noise filter.

  1. A162525
    Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A162526
    Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).


19. REMOVE OIL CONTROL VALVE FILTER

  1. A164313E03
    LH:
    Remove the 3 bolts, cylinder head cover spacer, gasket and filter.
    Text in Illustration 
    *1
    Cylinder Head Cover Spacer
    *2
    Gasket
    *3
    Filter

  1. A164314E03
    RH:
    Remove the 3 bolts, cylinder head cover spacer, gasket and filter.
    Text in Illustration 
    *1
    Cylinder Head Cover Spacer
    *2
    Gasket
    *3
    Filter


20. REMOVE SPARK PLUG TUBE GASKET

A164315E02
  1. Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

  1. Using a screwdriver, pry out the gaskets.

    Text in Illustration 
    *1
    Tape
    V100135
    Pry

    NOTICE:
    1. Be careful not to damage the cylinder head cover.
    2. Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.

    HINT:
    Tape the screwdriver tip before use.


21. REMOVE CRANKSHAFT PULLEY

  1. A164228E04
    Using SST, loosen the crankshaft pulley set bolt until 2 or 3 threads are engaged.
    SST
    09213-70011  
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. A164229E03
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)
    Text in Illustration 
    *a
    Hold
    V100135
    Turn


22. REMOVE WATER PUMP ASSEMBLY

  1. A151828
    Remove the 8 bolts, water pump and gasket.


23. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A237019
    Remove the 28 bolts and nut shown in the illustration.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. A162530
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

    HINT:
    Tape the screwdriver tip before use.

  1. A162531
    Remove the oil pump gasket from the cylinder block.

  1. A164415
    Remove the O-ring from the oil pan.


24. REMOVE WATER INLET PIPE

  1. A162532
    Remove the water inlet pipe.

  1. Remove the 2 O-rings from the water inlet pipe.


25. REMOVE FRONT CRANKSHAFT OIL SEAL

  1. A163996E02
    Place the timing chain cover on wooden blocks.

  1. Using a screwdriver and wooden block, pry out the oil seal.

    Text in Illustration 
    *1
    Wooden Block

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.


26. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the crankshaft pulley bolt.

  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing sprocket and camshaft timing gears are as shown in the illustration.

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.


    A160654E02
    Text in Illustration 
    *1
    Timing Mark
    *2
    Timing Mark Position
    *3
    Knock Pin Position
    *4
    Key
    *a
    Toward Ceiling
    *b
    Approximately 2°
    *c
    Approximately 45°
    *d
    Approximately 16°
    *e
    Approximately 18°
    *f
    Approximately 32°


27. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH

  1. A174140E02
    Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. A174141E02
    Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. A160733
    Remove the 2 bolts, chain tensioner and gasket.


28. REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH

A178535

29. REMOVE NO. 1 CHAIN VIBRATION DAMPER LH

A178536
  1. Remove the 2 bolts and chain vibration damper.


30. REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH

  1. A160655E02
    While pushing down the No. 3 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A160656E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.

  1. A160657E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    Be careful not to damage the cylinder head with the wrench.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.

  1. Remove the No. 1 and No. 2 chains from the gears.


31. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

A148225E01
  1. Remove the 2 bolts and chain tensioner.


32. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH

  1. A174142E02
    Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. A174143E02
    Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. A150146
    Remove the 2 bolts and chain tensioner.


33. REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH

A178486

34. REMOVE NO. 1 CHAIN VIBRATION DAMPER RH

A160658
  1. Remove the 2 bolts and vibration damper.


35. REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH

  1. A160659E02
    While raising up the No. 2 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A160660E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.

  1. A160661E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    Be careful not to damage the cylinder head with the wrench.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.

  1. Remove the No. 1 and No. 2 chains from the gears.


36. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

A148224E01
  1. Remove the 2 bolts and chain tensioner.


37. REMOVE CRANKSHAFT TIMING GEAR KEY

A145630
  1. Using a screwdriver, remove the 2 timing gear keys from the crankshaft.


38. REMOVE CAMSHAFT BEARING CAP LH

  1. A163591E03
    Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
    Text in Illustration 
    *1
    IN
    *2
    EX
    *3
    Knock Pin

  1. A163592E03
    Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. A163593E03
    Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the No. 3 and No. 4 camshafts.


39. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

  1. A163594
    Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.


40. REMOVE CAMSHAFT BEARING CAP RH

  1. A160683E03
    Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
    Text in Illustration 
    *1
    EX
    *2
    IN
    *3
    Knock Pin

  1. A160684E03
    Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. A160685E03
    Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the No. 1 and No. 2 camshafts.


41. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A160735
    Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.


42. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 32 valve rocker arms from the cylinder heads.

    HINT:
    Arrange the removed parts in the correct order.


43. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 32 valve lash adjusters from the cylinder heads.

    HINT:
    Arrange the removed parts in the correct order.


44. REMOVE VALVE STEM CAP
  1. Remove the 32 valve stem caps from the cylinder heads.

    HINT:
    Arrange the removed parts in the correct order.


45. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

  1. A160736E05
    Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.

  1. A160737E05
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

  1. Remove the cylinder head and gasket.


46. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

  1. A160738E04
    Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.

  1. A160739E03
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

  1. Remove the cylinder head and gasket.


47. REMOVE CYLINDER BLOCK WATER JACKET SPACER

A161997
  1. Remove the 2 water jacket spacers from the cylinder block.

    NOTICE:
    Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.


48. REMOVE VENTILATION PIPE GASKET

  1. A161915
    Using a screwdriver, pry out the ventilation pipe gasket.

    HINT:
    Tape the screwdriver tip before use.


49. REMOVE NO. 1 HEAT EXCHANGER COVER

  1. A237026
    Remove the 12 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. A164347
    Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.


50. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A237027
    Remove the 14 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. A120816
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


51. REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

  1. A237028
    Remove the 14 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    HINT:
    Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.

  1. A160722E03
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.


52. REMOVE NO. 1 OIL PAN BAFFLE PLATE

  1. A160723
    Remove the 7 bolts and baffle plate.


53. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A160724
    Remove the 2 bolts, oil strainer and O-ring.


54. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A145612
    Remove the 6 bolts and oil seal retainer.

  1. A145613
    Using a screwdriver, pry out the oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.


55. REMOVE OIL DRAIN PIPE SUB-ASSEMBLY

  1. A160728
    Remove the bolt and oil drain pipe.

  1. Remove the O-ring.


56. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A178527E02
    Place the oil seal retainer on wooden blocks.
    Text in Illustration 
    *1
    Wooden Block

  1. Using a screwdriver and hammer, tap out the oil seal.


57. REMOVE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.


58. REMOVE STUD BOLT

NOTICE:
If the stud bolt is deformed or its threads are damaged, replace it.

← REMOVAL (from Sep 2011)DISASSEMBLY (from Jan 2012) →