2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2012


1. REMOVE OIL FILTER ELEMENT

  1. A094910E10
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A207196
    Remove the oil filter drain plug.

  1. A272715E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A207198
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A207199E02
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A209947E02
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


2. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A163657
    Disconnect the oil pressure sender gauge connector.

  1. A162467
    Remove the oil pressure sender gauge.


3. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. A162469
    Remove the 2 bolts, 2 nuts and filter bracket.

  1. A162470
    Remove the 2 O-rings.


4. REMOVE CRANKSHAFT PULLEY

  1. A164228E03
    Using SST, remove the crankshaft pulley set bolt.
    SST
    09213-70011  
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. Temporarily install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.

  1. A164229E02
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)
    Text in Illustration 
    *a
    Hold
    V100135
    Turn


5. REMOVE OIL FILLER CAP SUB-ASSEMBLY
  1. Remove the oil filler cap.

  1. Remove the gasket from the oil filler cap.


6. REMOVE OIL FILLER CAP HOUSING

  1. A214596
    Remove the 2 bolts, oil filler cap housing and gasket.


7. REMOVE SPARK PLUG
  1. Using a 16 mm plug wrench, remove the 8 spark plugs.


8. REMOVE KNOCK SENSOR

  1. A230377
    Disconnect the 4 knock sensor connectors.

  1. Remove the 4 bolts and 4 knock sensors.


9. REMOVE VVT SENSOR

  1. A158607E05
    Disconnect the 4 VVT sensor connectors.
    Text in Illustration 
    *A
    for Bank 2
    *B
    for Bank 1

  1. Remove the 4 bolts and 4 VVT sensors.


10. REMOVE CAMSHAFT POSITION SENSOR

  1. A230353
    Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.


11. REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR

  1. A218679
    Remove the 2 bolts and crankshaft position sensor protector.


12. REMOVE CRANKSHAFT POSITION SENSOR

  1. A218680
    Disconnect the crankshaft position sensor connector.

  1. Remove the bolt and crankshaft position sensor.


13. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A214600
    for Bank 1:
    Remove the 2 bolts and 2 camshaft oil control valves.

  1. A214601
    for Bank 2:
    Remove the 2 bolts and 2 camshaft oil control valves.


14. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A163838E03
    Remove the 2 water drain cock plugs from the cylinder block water drain cocks.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side

  1. Remove the 2 cylinder block water drain cocks from the cylinder block.


15. REMOVE WATER INLET HOUSING

  1. A215871
    Remove the 3 bolts and water inlet housing.

  1. Remove the gasket from the engine water pump.


16. REMOVE FRONT WATER BY-PASS JOINT

  1. A229715
    Remove the 4 nuts, water by-pass joint and 2 gaskets.


17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A210022
    Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and cylinder head cover gasket LH.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A229745
    Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).
    Text in Illustration 
    V100143
    Gasket


18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A210024
    Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and cylinder head cover gasket RH.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A229746
    Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).
    Text in Illustration 
    V100143
    Gasket


19. REMOVE OIL CONTROL VALVE FILTER

  1. A164313E02
    for Bank 1:
    Remove the 3 bolts, cylinder head cover spacer, gasket and oil control valve filter.
    Text in Illustration 
    *1
    Cylinder Head Cover Spacer
    *2
    Gasket
    *3
    Oil Control Valve Filter

  1. A164314E02
    for Bank 2:
    Remove the 3 bolts, cylinder head cover spacer, gasket and oil control valve filter.
    Text in Illustration 
    *1
    Cylinder Head Cover Spacer
    *2
    Gasket
    *3
    Oil Control Valve Filter


20. REMOVE SPARK PLUG TUBE GASKET

  1. A218897E01
    Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
    Text in Illustration 
    *1
    Ventilation Baffle Plate Claw
    *2
    Protective Tape

  1. Using a screwdriver, pry out the gaskets.

    NOTICE:
    Be careful not to damage the cylinder head cover.

    HINT:
    1. Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.
    2. Tape the screwdriver tip before use.


21. REMOVE ENGINE OIL LEVEL SENSOR
  1. Disconnect the oil level sensor connector.

  1. A174186
    Remove the 4 bolts and oil level sensor.

  1. A216760E01
    Cut away part of the gasket and remove the gasket from the engine oil level sensor.
    Text in Illustration 
    *1
    Cutting Position
    *2
    Supply Part

    HINT:
    Remove the only the outer part of the gasket.


22. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A162527
    Remove the bolt, 6 mm hexagon bolt and belt tensioner.


23. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A210026
    Remove the 26 bolts and nut shown in the illustration.

  1. A229747
    Remove the timing chain cover by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.
    Text in Illustration 
    V100144
    Protective Tape

    NOTICE:
    Be careful not to damage the cylinder head, camshaft housing and cylinder block contact surfaces of the chain cover.

    HINT:
    Tape the screwdriver tip before use.

  1. A210028
    Remove the gasket from the cylinder block.

  1. A164415
    Remove the O-ring from the oil pan.


24. REMOVE ENGINE WATER PUMP ASSEMBLY

  1. A215872
    Remove the 8 bolts, engine water pump and gasket.


25. REMOVE WATER INLET PIPE

  1. A210029
    Remove the water inlet pipe.

  1. Remove the 2 O-rings from the water inlet pipe.


26. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Place the timing chain cover on wooden blocks.

  1. A214602E02
    Place the oil pump on a wooden block.
    Text in Illustration 
    *1
    Wooden Block
    *2
    Protective Tape

  1. Using a screwdriver and wooden block, pry out the front crankshaft oil seal.

    NOTICE:
    Do not damage the surface of the front crankshaft oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.


27. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the pulley set bolt.

  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.


    A214603E02
    Text in Illustration 
    *1
    Crankshaft Timing Gear Key
    *2
    Timing Mark
    *a
    Toward Ceiling
    *b
    Timing Mark Position
    *c
    Knock Pin Position
    *d
    Approximately 2°
    *e
    Approximately 45°
    *f
    Approximately 16°
    *g
    Approximately 18°
    *h
    Approximately 32°


28. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH

  1. A214604E02
    Move the stopper plate upward to release the lock and push the plunger deep into the No. 1 chain tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. A214605E02
    Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Hexagon Wrench

  1. A214606
    Remove the 2 bolts, No. 1 chain tensioner LH and gasket.


29. REMOVE CHAIN TENSIONER SLIPPER LH

A214607

30. REMOVE NO. 1 CHAIN VIBRATION DAMPER LH

  1. A214608
    Remove the 2 bolts and No. 1 chain vibration damper LH.


31. REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH

  1. A214609E02
    While pushing down the No. 3 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *3
    No. 3 Chain Tensioner
    *a
    Push

  1. A214610E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.

  1. A214611E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing exhaust gear.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.

  1. Remove the No. 1 and No. 2 chains from the gears.


32. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A214612
    Remove the 2 bolts and No. 3 chain tensioner.


33. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH

  1. A214613E02
    Move the stopper plate upward to release the lock and push the plunger deep into the No. 1 chain tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. A214614E02
    Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Hexagon Wrench

  1. A214615
    Remove the 2 bolts and No. 1 chain tensioner RH.


34. REMOVE CHAIN TENSIONER SLIPPER RH

A214616

35. REMOVE NO. 1 CHAIN VIBRATION DAMPER RH

  1. A214617
    Remove the 2 bolts and No. 1 chain vibration damper RH.


36. REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH

  1. A214618E02
    While raising up the No. 2 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *3
    No. 2 Chain Tensioner
    *a
    Push

  1. A214619E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.

  1. A214620E02
    Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing exhaust gear.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.

  1. Remove the No. 1 and No. 2 chains from the gears.


37. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A214621
    Remove the 2 bolts and No. 2 chain tensioner.


38. REMOVE CRANKSHAFT TIMING GEAR KEY

  1. A214622
    Using a screwdriver, remove the 2 crankshaft timing gear keys from the crankshaft.


39. REMOVE CAMSHAFT BEARING CAP LH

  1. A214623E02
    Make sure that the knock pins of the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *A
    for Intake Side
    *B
    for Exhaust Side
    *1
    Knock Pin

  1. A218891E01
    Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. A218892E01
    Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 camshaft bearing caps.

    HINT:
    Arrange the removed parts in the correct order.


40. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
  1. Remove the No. 3 camshaft from the camshaft housing LH.


41. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
  1. Remove the No. 4 camshaft from the camshaft housing LH.


42. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

  1. A214624E01
    Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.


43. REMOVE CAMSHAFT BEARING CAP RH

  1. A214625E02
    Make sure that the knock pins of the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *A
    for Exhaust Side
    *B
    for Intake Side
    *1
    Knock Pin

  1. A160684E05
    Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. A160685E04
    Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 camshaft bearing caps.

    HINT:
    Arrange the removed parts in the correct order.


44. REMOVE NO. 1 CAMSHAFT SUB-ASSEMBLY
  1. Remove the No. 1 camshaft from the camshaft housing RH.


45. REMOVE NO. 2 CAMSHAFT SUB-ASSEMBLY
  1. Remove the No. 2 camshaft from the camshaft housing RH.


46. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A214626E01
    Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.


47. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 32 No. 1 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


48. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 32 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


49. REMOVE VALVE STEM CAP
  1. Remove the 32 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


50. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

  1. A160736E07
    Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.

  1. A160737E07
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

  1. Remove the cylinder head LH.


51. REMOVE NO. 2 CYLINDER HEAD GASKET

52. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A160738E06
    Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.

  1. A160739E05
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

  1. Remove the cylinder head.


53. REMOVE CYLINDER HEAD GASKET

54. REMOVE CYLINDER BLOCK WATER JACKET SPACER

  1. A214628
    Remove the 2 cylinder block water jacket spacers from the cylinder block.

    NOTICE:
    Be sure to remove the cylinder block water jacket spacers. Otherwise, they may fall and become damaged when the cylinder block is inverted.


55. REMOVE OIL RETURN PIPE GASKET

  1. A214629E01
    Using a screwdriver, pry out the oil return pipe gasket.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


56. REMOVE VENTILATION PIPE GASKET

  1. A214630E01
    Using a screwdriver, pry out the ventilation pipe gasket.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


57. REMOVE NO. 1 HEAT EXCHANGER COVER

  1. A228434
    Remove the 12 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. A214632E01
    Remove the No. 1 heat exchanger cover by prying between the No. 1 heat exchanger cover and cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


58. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A274235
    Remove the 14 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. A120816
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


59. REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

  1. A274236
    Remove the 14 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

  1. A274237E01
    Remove the No. 1 oil pan by prying between the No. 1 oil pan and cylinder block with a screwdriver.
    Text in Illustration 
    *a
    for LH Side
    *b
    for RH Side

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and No. 1 oil pan.

    HINT:
    Tape the screwdriver tip before use.


60. REMOVE NO. 1 OIL PAN BAFFLE PLATE

  1. A274238
    Remove the 7 bolts and No. 1 oil pan baffle plate.


61. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A274239
    Remove the 2 bolts, oil strainer and O-ring.


62. REMOVE REAR ENGINE OIL SEAL RETAINER

  1. A145612
    Remove the 6 bolts and rear engine oil seal retainer.

  1. A145613
    Using a screwdriver, pry out the rear engine oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.


63. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A145614E05
    Place the rear engine oil seal retainer on wooden blocks.
    Text in Illustration 
    *1
    Wooden Block

  1. Using a screwdriver and hammer, tap out the rear crankshaft oil seal.


64. REMOVE OIL DRAIN PIPE SUB-ASSEMBLY

  1. A160728
    Remove the bolt and oil drain pipe.

  1. Remove the O-ring.


65. REMOVE RING PIN

NOTICE:
It is not necessary to remove a ring pin unless it is being replaced.


66. REMOVE STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.

← REMOVAL (from Jan 2012)INSPECTION (from Jan 2012) →