2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).
  2. Disconnect the cable from the negative (-) battery terminal to clear the diesel throttle valve fully closed position learned value.


2. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
  1. (Click here)


3. REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

  1. A257026
    Loosen the No. 1 air hose clamp.

  1. Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

  1. A257028
    Remove the 3 nuts, bolt and No. 1 cool air inlet.

  1. Remove the gasket from the air tube RH.


4. REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

  1. A257027
    Loosen the No. 2 air hose clamp.

  1. A257029
    Remove the 3 nuts, bolt and No. 2 cool air inlet.

  1. Remove the gasket from the air tube LH.


5. DISCONNECT NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A176580
    Remove the bolt and disconnect the oil level dipstick guide.


6. REMOVE AIR TUBE SUB-ASSEMBLY RH

A174729
  1. Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


7. DRAIN CLUTCH FLUID (for Manual Transmission)

8. REMOVE CLUTCH HOSE (for Manual Transmission)

  1. A177028
    Disconnect the 2 flexible hose tubes from the clutch hose with a 10 mm union nut wrench while holding the flexible hose with a wrench.

    NOTICE:
    1. Do not bend or damage the flexible hose tubes.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tubes from the connecting point.

  1. Remove the 2 clips.

  1. A183845
    Remove the bolt and clutch hose.


9. REMOVE AIR TUBE SUB-ASSEMBLY LH

A174728
  1. Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


10. REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177030
    Using a 10 mm union nut wrench, disconnect the tube connector to flexible hose tube from the clutch tube to release cylinder 2 way.

    NOTICE:
    1. Do not bend or damage the flexible hose tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tube from the connecting point.

  1. A177031
    Remove the 2 bolts and tube connector to flexible hose tube.


11. REMOVE DIESEL THROTTLE BODY ASSEMBLY RH

A163132
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


12. REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

A163131
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.

← ON-VEHICLE INSPECTION (from Sep 2011)REMOVAL (from Jan 2012) →