2011-2013 Land Cruiser · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. INSPECT AND ADJUST ADJUSTING SHIM

  1. C161909E01
    Measure the differential case LH and RH dimensions labeled X shown in the illustration.

  1. C179831E01
    Install the 3 thrust washers and 2 clutch plates to the side gear.

  1. Using SST to press down the thrust washers and clutch plates with a force of approximately 98 N*m (1000 kgf*cm, 72 ft.*lbf), measure dimension "Y" shown in the illustration.

    SST
    09649-17010  

  1. Referring to the following table, select the proper adjusting shim.

    Standard Adjusting Shim Thickness:
    Adjusting shim thickness = X - Y - 19.08 mm (0.751 in.)
    Mark
    Specified Condition
    A
    0.20 mm (0.00787 in.)
    B
    0.25 mm (0.00984 in.)
    C
    0.30 mm (0.0118 in.)
    D
    0.35 mm (0.0138 in.)


    C161911E02

    C161912E02


2. INSPECT REAR DIFFERENTIAL SIDE GEAR

  1. C124142
    Install the thrust washers, clutch plates and adjusting shim to the side gear.

    HINT:
    When installing the adjusting shim, make sure the surface with no oil groove faces the differential case side.

  1. Install the side gear to the differential case.

  1. Install the 4 pinion gears and thrust washers to the spider.

  1. C161913
    Align the spring retainer holes with the straight pins and install the retainer.

  1. Install the spider assembly to the differential case.

    HINT:
    Install the spider to the differential case tightly and do not move the spring retainer.

  1. C161914
    Using the dial indicator, measure the side gear backlash while holding the side gear and spider.

    Standard backlash:
    0.02 to 0.15 mm (0.000787 to 0.00591 in.)

    HINT:
    1. Measure at all 4 pinion gear locations.
    2. Measure the backlash at the differential case LH and RH.
    3. Apply hypoid gear oil LSD to each sliding surface and rotating part.

    If the backlash is not within the specification, replace the side gear thrust washers with washers of a different thickness.


3. ASSEMBLE DIFFERENTIAL CASE
  1. Install the spider assembly to the differential case LH.

    HINT:
    Install the spider to the differential case LH tightly and do not move the spring retainer.

  1. Install the compression spring and spring retainer RH.

  1. Install the side gear assembly RH.

    NOTICE:
    1. Be careful not to drop the side gear.
    2. Check the pinion and side gear alignment.

  1. C161843E05
    Align the matchmarks and assemble the differential case LH and RH.

  1. Install the 8 bolts and tighten them uniformly, a little at a time.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }


4. INSTALL REAR DIFFERENTIAL CASE BEARING

  1. C161847E02
    Using SST and a press, press the RH side bearing (inner race) into the differential case.
    SST
    09710-30050  
    09950-70010   (09951-07150)

  1. C161848E02
    Using SST and a press, press the LH side bearing (inner race) into the differential case.
    SST
    09710-30050  
    09950-60010   (09951-00480)
    09950-70010   (09951-07150)


5. INSTALL DIFFERENTIAL RING GEAR
  1. Clean the threads of the bolts and differential case with non-residue solvent.

  1. Clean the contact surface of the differential case and ring gear.

  1. C161849E02
    Heat the ring gear to about 100°C (212°F) in boiling water.

  1. Carefully take the ring gear out of the boiling water.

  1. After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the ring gear and differential case and set the ring gear onto the differential case. Then temporarily install the 12 bolts so that the bolt holes in the ring gear and differential case are aligned.

  1. C161840E02
    After the ring gear cools down sufficiently, remove the 12 bolts. Then apply thread lock adhesive to the 12 bolts and install them.

    Thread lock:
    Toyota Genuine Adhesive 1360 K, Three Bond 1360 K or equivalent

    Torque:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }


6. INSPECT DIFFERENTIAL RING GEAR RUNOUT
  1. Place the bearing outer races on their respective bearings.

    HINT:
    Do not interchange the left and right outer races.

  1. Install the assembled plate washers to the side bearing.

  1. Install the differential case to the differential carrier.

    HINT:
    If it is difficult to install the differential case to the carrier, replace the plate washer with a thinner one. However, select a plate washer that allows no clearance between it and the carrier.

  1. Align the matchmarks on the bearing caps and differential carrier.

  1. Install and uniformly tighten the 4 bolts a little at a time.

  1. C161850
    Using a dial indicator, measure the ring gear runout.

    Maximum runout:
    0.05 mm (0.00197 in.)

    If the runout is more than the maximum, replace the ring gear.

  1. Remove the differential case.


7. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C161851E03
    Using SST and a press, press in the bearing (outer race).
    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)


8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C162726E03
    Using SST and a press, press in the bearing (outer race).
    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)


9. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING
  1. Install the washer to the drive pinion.

    HINT:
    After installing the washer, check the tooth contact pattern. If necessary, replace the washer with one of a different thickness.

  1. C161852E02
    Using SST and a press, press the rear bearing (inner race) into the drive pinion.
    SST
    09506-35010  


10. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

  1. C028218
    Install the drive pinion, front bearing (inner race) and oil slinger.

    HINT:
    Install the spacer and oil seal after adjusting the gear contact pattern.

  1. C161853E02
    Using SST, install the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

  1. C161854E02
    Using SST to hold the companion flange, install the nut.
    SST
    09330-00021   (09330-00030)

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf }

    NOTICE:
    1. Apply hypoid gear oil LSD to the nut.
    2. As there is no spacer, tighten a little at a time, being careful not to overtighten it.

  1. C124126
    Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Bearing
    Specified Condition
    New
    1.0 to 1.7 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf)
    Reused
    0.9 to 1.4 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)

    HINT:
    Measure the total preload after turning the bearing clockwise and counterclockwise several times to make the bearing smooth.


11. INSTALL REAR DIFFERENTIAL CASE SUB-ASSEMBLY
  1. Place the bearing outer races on their respective bearings.

    HINT:
    Do not interchange the left and right outer races.

  1. Install the differential case to the carrier.

    HINT:
    Make sure that there is backlash between the ring gear and drive pinion.


12. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT

  1. C161855
    Install the 2 adjusting nuts to the carrier, making sure the nuts are threaded properly.


13. INSPECT DIFFERENTIAL RING GEAR BACKLASH

  1. C161856E03
    Align the matchmarks on the bearing caps and carrier. Screw in the 4 bearing cap bolts 2 or 3 turns and press down the bearing caps by hand.

    HINT:
    If the bearing caps do not fit tightly on the carrier, the adjusting nuts are not engaged properly. Reinstall the adjusting nuts if necessary.

  1. C161857
    Tighten the 4 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }

  1. C161858E03
    Loosen the 4 bolts to the point where the adjusting nuts can be turned by SST.
    SST
    09504-00011  

  1. Using SST, tighten the adjusting nut on the ring gear side until the ring gear has a backlash of about 0.2 mm (0.00787 in.).

  1. C161859E02
    While turning the ring gear, use SST to tighten the adjusting nut on the drive pinion side. After the bearings are settled, loosen the adjusting nut on the drive pinion side.
    SST
    09504-00011  

  1. C161860E02
    Place a dial indicator on the top of the adjusting nut on the ring gear side.

  1. Adjust the side bearing to 0 preload by tightening the other adjusting nut until the pointer on the indicator begins to move.

  1. C161859E02
    Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.
    SST
    09504-00011  

  1. C161861E04
    Using a dial indicator, adjust the ring gear backlash until it is within the specification.
    SST
    09504-00011  

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    HINT:
    The backlash is adjusted by turning the left and right adjusting nuts by an equal amount. For example, loosen the nut on the left side 1 notch and tighten the nut on the right side 1 notch.

  1. Tighten the 4 bearing cap bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }

  1. After rotating the ring gear 5 turns or more, recheck the ring gear backlash.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)


14. INSPECT TOTAL PRELOAD

  1. C124126
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Drive Pinion Preload (at Starting):
    Bearing
    Specified Condition
    New
    Standard drive pinion preload plus
    0.4 to 0.6 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf)
    Reused
    Standard drive pinion preload plus
    0.4 to 0.6 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf)


15. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

  1. C161916
    Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.

  1. Turn the companion flange in both directions to inspect the ring gear for proper tooth contact.

    C116070E03
    If the teeth are not contacting properly, use the following table to select a proper washer for correction.

    Standard Washer Thickness:
    Specified Condition
    Specified Condition
    1.04 to 1.06 mm (0.0409 to 0.0417 in.)
    1.315 to 1.335 mm (0.0518 to 0.0526 in.)
    1.065 to 1.085 mm (0.0420 to 0.0427 in.)
    1.34 to 1.36 mm (0.0528 to 0.0535 in.)
    1.09 to 1.11 mm (0.0419 to 0.0437 in.)
    1.365 to 1.385 mm (0.0537 to 0.0545 in.)
    1.115 to 1.135 mm (0.0439 to 0.0447 in.)
    1.39 to 1.41 mm (0.0547 to 0.0555 in.)
    1.14 to 1.16 mm (0.0449 to 0.0457 in.)
    1.415 to 1.435 mm (0.0558 to 0.0565 in.)
    1.165 to 1.185 mm (0.0459 to 0.0467 in.)
    1.44 to 1.46 mm (0.0567 to 0.0575 in.)
    1.19 to 1.21 mm (0.0469 to 0.0476 in.)
    1.465 to 1.485 mm (0.0577 to 0.0585 in.)
    1.215 to 1.235 mm (0.0478 to 0.0486 in.)
    1.49 to 1.51 mm (0.0587 to 0.0595 in.)
    1.24 to 1.26 mm (0.0488 to 0.0496 in.)
    1.515 to 1.535 mm (0.0597 to 0.0605 in.)
    1.265 to 1.285 mm (0.0498 to 0.0506 in.)
    1.54 to 1.56 mm (0.0607 to 0.0615 in.)
    1.29 to 1.31 mm (0.0508 to 0.0516 in.)
    -


16. REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

  1. C161836E02
    Using SST to hold the flange, remove the nut.
    SST
    09330-00021   (09330-00030)


17. REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

  1. C161837E02
    Using SST, remove the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


18. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

19. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C124133E03
    Using SST, remove the front bearing (inner race) from the drive pinion.
    SST
    09556-22010  
    If the front bearing is damaged or worn, replace the bearing.


20. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new spacer to the drive pinion.


21. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C161827E02
    Using SST and a hammer, tap in the bearing (outer race).
    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the bearing (inner race).


22. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

23. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C161864E01
    Using SST and a hammer, tap in a new oil seal.
    SST
    09214-76011  

    Standard oil seal depth:
    0.05 to 0.95 mm (0.00197 to 0.0374)

  1. Coat the lip of the oil seal with MP grease.


24. INSTALL REAR DRIVE PINION REAR COMPANION FLANGE SUB-ASSEMBLY

  1. C161853E02
    Using SST, install the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


25. INSPECT DRIVE PINION PRELOAD
  1. Coat the threads of a new nut with hypoid gear oil.

  1. ZK09978E04
    Using SST to hold the companion flange, install the nut by tightening it until the standard preload is reached.
    SST
    09330-00021   (09330-00030)

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less

  1. C124126
    Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Bearing
    Specified Condition
    New
    1.0 to 1.7 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf)
    Reused
    0.9 to 1.4 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)


26. INSPECT TOTAL PRELOAD

  1. C124126
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Drive Pinion Preload (at Starting):
    Bearing
    Specified Condition
    New
    Standard drive pinion preload plus
    0.4 to 0.6 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf)
    Reused
    Standard drive pinion preload plus
    0.4 to 0.6 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf)


27. INSPECT DIFFERENTIAL RING GEAR

  1. C161872
    Using a dial indicator, measure the ring gear backlash.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    HINT:
    Measure at 3 or more positions around the circumference of the ring gear.

    If the backlash is not as specified, adjust the side bearing preload or repair as necessary.


28. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

  1. F001237E12
    Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum Runout:
    Runout
    Specified Condition
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    If the runout is more than the maximum, replace the companion flange.


29. STAKE DRIVE PINION COMPANION FLANGE REAR NUT

  1. C161318
    Using a chisel and hammer, stake the nut.


30. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

  1. C161917
    Install 2 new nut locks to the bearing caps.

  1. Install the 2 bolts, and bend the nut locks.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

← DISASSEMBLY (from Sep 2011)INSTALLATION (from Sep 2011) →