2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built from Sep 2011


1. CONNECT NO. 7 WATER BY-PASS HOSE

  1. A164188E03
    Connect the water by-pass hose to the fuel cooler.

    HINT:
    1. Align the alignment marks and connect the hose.
    2. Align the pinching portion of the clamp with the hose alignment mark and connect the hose.


2. INSTALL FUEL COOLER ASSEMBLY

  1. A176378
    Install the fuel cooler with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


3. CONNECT NO. 3 FUEL HOSE

  1. A181375
    Connect the fuel hose to the fuel cooler.

    HINT:
    1. Align the alignment marks and connect the hose.
    2. Align the pinching portion of the clamp with the hose alignment mark and connect the hose.


4. CONNECT NO. 6 WATER BY-PASS HOSE

A174806

5. INSTALL NO. 4 NOZZLE LEAKAGE PIPE

  1. A174805E01
    Temporarily install a new gasket and the No. 4 nozzle leakage pipe with the union bolt and bolt.

  1. Tighten the union bolt and bolt in the order shown in the illustration.

    Torque:
    for union bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the No. 2 fuel hose to the fuel cooler.


6. INSTALL NO. 3 NOZZLE LEAKAGE PIPE

  1. A174804E01
    Temporarily install a new gasket and the No. 3 nozzle leakage pipe with the union bolt and bolt.

  1. Tighten the union bolt and bolt in the order shown in the illustration.

    Torque:
    for union bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the No. 1 fuel hose to the fuel cooler.


7. INSTALL EGR COOLER INSULATOR (w/ EGR System)

A174803

8. INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

  1. A174802
    Connect the No. 5 water by-pass hose to the water by-pass outlet.

  1. A174801E01
    Install 2 new gaskets and the EGR valve with EGR cooler with the 6 bolts labeled A and 4 bolts labeled B shown in the illustration.

    Torque:
    for bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt B:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    HINT:
    The gasket claws should face toward the No. 1 and No. 2 EGR pipes.


9. INSTALL EGR PIPE INSULATOR (w/ EGR System)

  1. A174800
    Install the EGR pipe insulator with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    If the No. 1 and No. 2 EGR pipe insulator installation stay is deformed, or the bolt holes of the EGR pipe insulator do not align, replace the No. 1 and No. 2 EGR pipes as a set.


10. INSTALL INTAKE MANIFOLD INSULATOR (w/ EGR System)

A174799

11. INSTALL NO. 3 INTAKE MANIFOLD

A174867E01
  1. Set 2 new gaskets to the No. 1 and No. 2 intake manifolds.

  1. Install the No. 3 intake manifold with the 16 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Bolt Length 
    Item
    Length
    Bolt A
    25 mm (0.984 in.)
    Bolt B
    70 mm (2.76 in.)


12. CONNECT NO. 2 ENGINE WIRE

  1. A174797E01
    Connect the No. 2 engine wire with the 3 bolts.

    Torque:
    for bolt A:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Attach the 2 wire harness clamps.


13. INSTALL INTAKE PIPE

  1. A174796
    w/ EGR System:
    Install 2 new gaskets and the intake pipe with the 6 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A180252
    w/o EGR System:
    Install a new gasket and the intake pipe with the 4 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


14. INSTALL NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174791

15. INSTALL NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174795

16. INSTALL COMMON RAIL ASSEMBLY LH AND RH
  1. Install the common rail assembly LH and RH (Click here).

← REMOVAL (from Sep 2011)COMPONENTS (from Sep 2011) →