2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

NOTICE:
When replacing an injector (including interchanging injectors between cylinders), common rail, replace the corresponding injection pipes with a new one.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the cables from the negative (-) main battery and sub-battery terminals.


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. A174148
    Remove the 3 bolts and screw.

  1. Loosen the clip and remove the splash shield.


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Remove the 3 bolts and screw.

  1. Loosen the clip and remove the splash shield.


4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and under cover.


5. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 7 clips and upper radiator support seal.


6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator reservoir cap to drain the coolant in the radiator.

  1. Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

    A174741E01

  1. Tighten the radiator drain cock plug by hand.

  1. A177208
    Tighten the oil filter bracket drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


7. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
  1. Remove the intercooler assembly (Click here).


8. REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

  1. A257026
    Loosen the No. 1 air hose clamp.

  1. Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

  1. A257028
    Remove the 3 nuts, bolt and No. 1 cool air inlet.

  1. Remove the gasket from the air tube RH.


9. REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

  1. A257027
    Loosen the No. 2 air hose clamp.

  1. A257029
    Remove the 3 nuts, bolt and No. 2 cool air inlet.

  1. Remove the gasket from the air tube LH.


10. DISCONNECT WATER HOSE SUB-ASSEMBLY

A174687E01

11. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A174875
    Disconnect the wire harness clamp from the No. 2 engine oil level dipstick guide.

  1. A170321
    Disconnect the ventilation hose from the cylinder head cover RH.

  1. Remove the 2 bolts and No. 2 engine oil level dipstick guide.

  1. Remove the O-ring from the No. 2 engine oil level dipstick guide.


12. REMOVE AIR TUBE SUB-ASSEMBLY RH

A174729
  1. Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


13. REMOVE DIESEL THROTTLE BODY ASSEMBLY RH

A163132
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


14. DRAIN CLUTCH FLUID (for Manual Transmission)

15. REMOVE CLUTCH HOSE (for Manual Transmission)

  1. A177028
    Disconnect the 2 flexible hose tubes from the clutch hose with a 10 mm union nut wrench while holding the flexible hose with a wrench.

    NOTICE:
    1. Do not bend or damage the flexible hose tubes.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tubes from the connecting point.

  1. Remove the 2 clips.

  1. A183845
    Remove the bolt and clutch hose.


16. REMOVE AIR TUBE SUB-ASSEMBLY LH

A174728
  1. Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


17. REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177030
    Using a 10 mm union nut wrench, disconnect the tube connector to flexible hose tube from the clutch tube to release cylinder 2 way.

    NOTICE:
    1. Do not bend or damage the flexible hose tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tube from the connecting point.

  1. A177031
    Remove the 2 bolts and tube connector to flexible hose tube.


18. REMOVE NO. 1 GAS FILTER

  1. A163347
    Disconnect the hose from the intake pipe.

  1. Remove the gas filter.


19. REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

  1. A185151
    for Manual Transmission:

    1. Remove the bolt and disconnect the clutch tube to release cylinder 2 way from the bracket.

  1. A163348
    Remove the 2 bolts and bracket.


20. REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

A163131
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


21. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A174698
    Loosen the hose clamp.

  1. Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.

  1. Detach the 4 clamps and remove the air cleaner cap.


22. REMOVE NO. 1 AIR CLEANER HOSE

  1. A174699
    Loosen the hose clamp and remove the No. 1 air cleaner hose.


23. REMOVE INTAKE AIR CONNECTOR

  1. A174749E01
    w/o Viscous Heater:

    1. Disconnect the connector from the water temperature sensor.

    2. Using a clip remover, detach the 3 wire harness clamps.

  1. w/ Viscous Heater:

    1. Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.

    2. Using a clip remover, detach the 3 wire harness clamps.

  1. A174710
    Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.


24. REMOVE NO. 3 AIR TUBE

  1. A174751
    Disconnect the wire harness from the clamp.

  1. Remove the nut and ground wire.

  1. A174752
    Remove the bolt and disconnect the wire harness bracket.

  1. A174708
    Loosen the hose clamp and remove the bolt and No. 3 air tube.


25. REMOVE NO. 2 AIR HOSE

  1. A177375
    Loosen the hose clamp and remove the No. 2 air hose.


26. REMOVE NO. 4 AIR TUBE

  1. A174690
    Remove the bolt and disconnect the suction hose.

  1. A174706
    Loosen the hose clamp and remove the bolt and No. 4 air tube.


27. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174711
    Disconnect the ventilation hose from the oil separator.

  1. Loosen the hose clamp.

  1. Remove the bolt and No. 2 air cleaner pipe.


28. REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

  1. A174689
    Remove the 4 bolts and disconnect the 4 water hose ends, and then remove the heater water pipe.


29. REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174714
    Loosen the hose clamp.

  1. Remove the bolt and No. 1 air cleaner pipe.


30. DISCONNECT FUEL HOSE

A174685E01

31. REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

  1. A174688
    Remove the 2 bolts and disconnect the 2 water hose ends, and then remove the No. 3 water by-pass pipe.


32. REMOVE NO. 4 WATER BY-PASS PIPE

  1. A174691
    w/ EGR System:

    1. Remove the 2 bolts and nut.

    2. Disconnect the 4 water hose ends, and then remove the No. 4 water by-pass pipe.

  1. A174692
    w/o EGR System:

    1. Remove the 2 bolts and nut.

    2. Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.


33. DISCONNECT ENGINE WIRE

  1. LH Side:

    1. A174754
      Disconnect the 4 connectors.

    2. Using a clip remover, detach the 3 wire harness clamps.

    3. A174755
      Disconnect the 2 connectors.

    4. Using a clip remover, detach the 3 wire harness clamps.

    5. A174756E01
      Disconnect the 8 connectors.

    6. Remove the bolt and engine wire harness bracket labeled B.

    7. Remove the 2 bolts and disconnect the engine wire protector labeled A.

    8. for RHD:
      Disconnect the wire harness from the wire harness clamp holder labeled C.

  1. RH Side:

    1. A174750E01
      Disconnect the 7 connectors.

    2. Using a clip remover, detach the wire harness clamp.

    3. Remove the 3 bolts and disconnect the wire harness protector labeled A.

    4. Remove the bolt and wire harness bracket labeled B.

    5. Remove the nut and glow plug wire harness labeled C.

    6. A174759
      for RHD:
      Disconnect the wire harness from the wire harness clamp holder.

  1. Rear Side:

    1. A174757E01
      Using a clip remover, detach the wire harness clamp.

    2. Remove the 2 bolts and 2 ground wires labeled C.

    3. Remove the 2 bolts and disconnect the engine wire harness protector labeled B.

    4. Disconnect the 2 common rail connectors.

    5. Remove the nut and disconnect the glow plug wire harness labeled A.


34. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

NOTICE:
A174693
  1. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel pipe ends, cover the fuel pipe ends with plastic bags.
  2. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel supply pump hole, cover the hole with protective tape.

  1. Disconnect the fuel hose from the No. 5 nozzle leakage pipe.

  1. Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the union bolt and gasket.

  1. Remove the bolt, nut and No. 2 fuel pipe.


35. REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes, cover the holes with protective tape.

  1. A185542
    w/ EGR System:

    1. Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the 2 nuts and 2 No. 2 injection pipe clamps.

    3. Remove the No. 6 injection pipe.

  1. A174695
    w/o EGR System:

    1. Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the nut and No. 2 injection pipe clamp.

    3. Remove the bolt and No. 6 injection pipe.


36. REMOVE INJECTION PIPE LH

  1. A174694
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.

  1. A174789
    Using a union nut wrench, remove the 4 injection pipes.

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


37. REMOVE COMMON RAIL ASSEMBLY LH

  1. A176404
    Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the fuel pressure limiter from the common rail. If it is removed, replace the common rail.


38. REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

  1. A174697
    Disconnect the 2 hoses from the fuel pipe.

  1. Remove the bolt and fuel filter to injection pump fuel pipe.


39. REMOVE INJECTION PIPE RH

  1. A174788
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.

  1. A174793
    Using a union nut wrench, remove the 4 injection pipes.

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


40. DISCONNECT NO. 2 ENGINE WIRE

  1. A174797
    Remove the 3 bolts and using a clip remover, detach the 2 wire harness clamps, and then disconnect the No. 2 engine wire.


41. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (for Engine Mounting)

  1. A174969
    Disconnect the 2 vacuum hoses.

  1. Remove the bolt and vacuum switching valve.


42. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

  1. A264755
    w/ Intercooler:
    Disconnect the 2 vacuum hoses.

  1. A264102
    Remove the 3 bolts and vacuum transmitting pipe.


43. DISCONNECT NO. 3 VENTILATION HOSE

A177382

44. REMOVE CYLINDER HEAD COVER SILENCER LH (w/ Intercooler)

  1. A174975
    Remove the 3 bolts and cylinder head cover silencer.


45. REMOVE NOZZLE HOLDER SEAL LH

  1. A164170
    Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

    HINT:
    Tape the screwdriver tip before use.


46. REMOVE OIL SEPARATOR ASSEMBLY

  1. A164169
    Remove the 3 bolts, oil separator and gasket.


47. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A164162
    Remove the 17 bolts, cylinder head cover and gasket.


48. REMOVE NOZZLE HOLDER GASKET LH

  1. A174977
    Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

    HINT:
    Tape the screwdriver tip before use.


49. DISCONNECT NO. 2 VENTILATION HOSE

A177397

50. REMOVE CYLINDER HEAD COVER SILENCER RH (w/ Intercooler)

  1. A174974
    Remove the 3 bolts and cylinder head cover silencer.


51. REMOVE NOZZLE HOLDER SEAL RH

  1. A164171
    Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

    HINT:
    Tape the screwdriver tip before use.


52. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A174971
    Remove the 18 bolts, cylinder head cover and gasket.


53. REMOVE NOZZLE HOLDER GASKET RH

  1. A174977
    Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

    HINT:
    Tape the screwdriver tip before use.


54. REMOVE FUEL INJECTOR RH

  1. A176409E01
    Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A164166
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


55. REMOVE FUEL INJECTOR LH

  1. A176410E01
    Remove the union bolt, 4 hollow screws, 5 gaskets and No. 2 nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A164165
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →