2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


4. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


5. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Using a clip remover, remove the 3 clips and fender apron seal.


6. REMOVE FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Using a clip remover, remove the 4 clips and fender apron seal.


7. REMOVE FRONT FENDER APRON SEAL LH

  1. A177004
    Using a clip remover, remove the 3 clips and fender apron seal.


8. REMOVE FRONT FENDER APRON SEAL REAR LH

  1. A177005
    Using a clip remover, remove the 4 clips and fender apron seal.


9. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the dipstick.

  1. Connect the wire harness clamp.


10. REMOVE TAILPIPE ASSEMBLY
  1. Remove the bolt, clamp and gasket.

  1. Remove the tailpipe from the 2 exhaust pipe supports.

  1. Remove the bolt and clamp, and then disconnect the tailpipe from the center exhaust pipe.


11. REMOVE CENTER EXHAUST PIPE ASSEMBLY
  1. Remove the 4 bolts.

  1. Remove the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the 2 gaskets from the front exhaust pipe and front No. 2 exhaust pipe.


12. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the bolt and disconnect the wire harness clamp bracket of the oxygen sensor from the transmission.

  1. Remove the 2 nuts, front No. 2 exhaust pipe and gasket from the exhaust manifold LH.


13. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the bolt and disconnect the wire harness clamp bracket of the oxygen sensor from the transmission.

  1. Remove the 2 nuts, front exhaust pipe and gasket from the exhaust manifold RH.


14. REMOVE PROPELLER SHAFT HEAT INSULATOR

  1. A175007
    Remove the 2 bolts and heat insulator.


15. REMOVE NO. 2 MANIFOLD STAY

  1. A184508
    Remove the 3 bolts and manifold stay.


16. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A184509
    Remove the 3 bolts and heat insulator.


17. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A236969
    Remove the 8 nuts, exhaust manifold and gasket.


18. REMOVE NO. 1 MANIFOLD STAY

  1. A184511
    Remove the 3 bolts and manifold stay.


19. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A184512
    Remove the 3 bolts and heat insulator.


20. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A236970
    Remove the 8 nuts, exhaust manifold and gasket.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →