2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174123E02
    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Tighten the radiator drain cock plug by hand.


5. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A174196E03
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet


6. REMOVE NO. 1 RADIATOR HOSE

7. REMOVE FAN SHROUD

  1. A151842
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A238869
    Disconnect the reservoir hose from the upper radiator tank.

  1. Detach the claw to open the flexible hose clamp.

  1. Remove the 2 bolts and disconnect the oil cooler tube from the fan shroud.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley.


8. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A163657
    Disconnect the sender gauge connector.

  1. A162467
    Remove the oil pressure sender gauge.


9. DISCONNECT COOLER COMPRESSOR ASSEMBLY

  1. A178491
    Remove the 3 bolts, nut and stud bolt, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


10. DISCONNECT NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A163800
    Remove the 3 bolts and disconnect the 2 water by-pass hoses from the oil cooler.


11. REMOVE NO. 1 OIL COOLER BRACKET

  1. A163672
    Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.


12. REMOVE OIL FILTER BRACKET

  1. A162469
    Remove the 2 bolts, 2 nuts and filter bracket.

  1. A162470
    Remove the 2 O-rings.


13. REMOVE CRANKSHAFT PULLEY

  1. A164228E04
    Using SST, loosen the crankshaft pulley set bolt until 2 or 3 threads are engaged.
    SST
    09213-70011  
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. A164229E03
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)
    Text in Illustration 
    *a
    Hold
    V100135
    Turn


14. REMOVE CRANKSHAFT TIMING GEAR KEY

  1. A163993
    Remove the crankshaft timing gear key from the crankshaft.


15. REMOVE FRONT CRANKSHAFT OIL SEAL

  1. A163774
    Using a screwdriver, pry out the oil seal.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole and crankshaft.

    HINT:
    Tape the screwdriver tip before use.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →