2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the cables from the negative (-) main battery and sub-battery terminals.


3. REMOVE ENGINE ASSEMBLY
  1. Remove the engine assembly from the vehicle (Click here).


4. REMOVE NO. 1 INTAKE AIR CONNECTOR PIPE

  1. A174753
    Remove the 4 connectors.

  1. Using a clip remover, detach the 5 wire harness clamps.

  1. A177381
    Loosen the hose clamp, and remove the bolt and No. 1 intake air connector pipe.


5. REMOVE GENERATOR ASSEMBLY

  1. A174761
    Remove the nut and bolt, and disconnect the generator positive (+) cable.

  1. A163035
    Remove the 3 bolts, 2 nuts and generator.


6. DISCONNECT NO. 1 OUTLET TURBO OIL HOSE

A177402

7. REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A170301
    Remove the 2 bolts and No. 1 engine oil level dipstick guide.


8. DISCONNECT NO. 2 OUTLET TURBO OIL HOSE

A177388

9. DISCONNECT NO. 2 INLET TURBO OIL PIPE SUB-ASSEMBLY

  1. A177391
    Remove the union bolt and gasket, and disconnect the No. 2 inlet turbo oil pipe.


10. REMOVE STIFFENER INSULATOR RH (w/ Intercooler)

  1. A170322
    Remove the 2 bolts and stiffener insulator RH.


11. DISCONNECT NO. 1 OIL COOLER HOSE

A177371E01

12. DISCONNECT NO. 2 OIL COOLER HOSE

13. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A177437
    Remove the 3 bolts and V-ribbed belt tensioner bracket.

  1. A174864
    Remove the bolt and No. 1 idler pulley.

  1. A177414
    Remove the 5 bolts and V-ribbed belt tensioner.


14. REMOVE CRANKSHAFT PULLEY

NOTICE:
A181685E01
This procedure is intended for removal/installation of the crankshaft pulley only. Do not use this procedure for removal/installation of the flywheel or the drive plate and ring gear.

  1. Install the 2 bolts to the bolt holes of the crankshaft rear side.

  1. Using a bar, turn the crankshaft until the crankshaft pulley service hole is a little to the left of bottom dead center.

  1. Install a 14 mm x 1.5 pitch service bolt with a length of 70 mm or more to the crankshaft pulley service hole, and hold the crankshaft using the timing chain cover protrusion.

  1. Remove the 3 bolts and crankshaft pulley.

    NOTICE:
    If the crankshaft pulley cannot be removed, temporarily install a bolt to the crankshaft so that the pulley does not fall, and lightly tap the outer edge of the mass damper with a plastic-faced hammer to remove the pulley. Do not tap the pulley V-ribbed belt ribs, as the crankshaft may be damaged.


15. REMOVE TIMING GEAR COVER SPACER (w/ Intercooler)

  1. A177415
    Remove the 2 bolts and timing gear cover spacer.


16. REMOVE OIL FILTER ELEMENT

  1. A174852
    Remove the oil filter drain plug.

  1. A094910E04
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

  1. Remove the O-ring from the oil filter drain plug and install it to the drain pipe.

  1. A174853E01
    Install the oil filter drain pipe to the oil filter cap and drain the engine oil.

  1. Remove the oil filter drain pipe.

  1. Apply a light coat of engine oil to a new O-ring, and install it to the oil filter drain plug.

  1. A174852
    Install the oil filter drain plug to the oil filter cap.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. A174854E01
    Using SST, remove the oil filter cap.
    SST
    09228-06501  

    HINT:
    Use a container to catch the draining oil. After the oil filter cap is loosened approximately 4 turns and the cap ribs are vertical, engine oil drains from the gap between the oil filter cap and oil pan.

  1. A106167E05
    Remove the oil filter element and O-ring from the oil filter cap.

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


17. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. A174758
    Disconnect the 2 wire harness clamps.

  1. A177438
    Remove the 3 bolts, 2 nuts and oil filter bracket.

  1. A177439
    Remove the 2 O-rings.


18. REMOVE ENGINE OIL LEVEL SENSOR

  1. A174870
    Remove the 4 bolts and engine oil level sensor.

  1. Remove the gasket.


19. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A174871
    Remove the 10 bolts and 2 nuts.

  1. A174872
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the No. 1 and No. 2 oil pans.


20. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A174873
    Remove the 2 bolts and oil strainer.

  1. Remove the O-ring from the oil strainer.


21. REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

  1. A174874E02
    Remove the 20 bolts, 2 nuts and oil reflector plate.

    NOTICE:
    If the oil reflector plate is deformed, replace it.

    HINT:
    Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.

  1. A177413
    Remove the No. 1 oil pan by prying between the No. 1 oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A174876
    Remove the 3 O-rings.

  1. A179094
    Remove the cylinder block oil hole gasket.


22. REMOVE REAR ENGINE OIL SEAL RETAINER

  1. A161974
    Remove the 10 bolts.

  1. Remove the oil seal retainer by prying between the oil seal retainer and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.


23. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A164590
    Place the oil seal retainer on wooden blocks.

  1. Using a screwdriver and hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


24. REMOVE SCAVENGING PUMP ASSEMBLY

  1. A161978
    Remove the 4 bolts and scavenging pump.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →