2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor while the engine speed is approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the cables from the negative (-) main battery and sub-battery terminals.


3. REMOVE MAIN BATTERY

4. REMOVE SUB-BATTERY

5. REMOVE FRONT WHEEL

6. REMOVE HOOD SUB-ASSEMBLY

  1. A174152
    Remove the 2 hood stay bolts. Then disconnect the 2 hood supports.

    NOTICE:
    1. Avoid touching the stroke portions of the rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinders while servicing.
    2. Do not wear cotton gloves or other similar materials when handling the rod. Fibers may attach to the rod and result in gas leaks.
    3. Do not apply any load to the cylinders in the horizontal direction in order to prevent the rod from being deformed.
    4. Remove the hood support while supporting the hood by hand.

  1. Remove the 4 bolts and hood.


7. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 7 clips and upper radiator support seal.


8. REMOVE FRONT FENDER MAIN SEAL LH

  1. B181061
    Using a clip remover, detach the 3 clips and remove the fender main seal.


9. REMOVE FRONT FENDER MAIN SEAL RH

HINT:
Use the same procedures described for the LH side.


10. REMOVE FRONT WIPER ARM LH
  1. Remove the nut, wiper arm and blade.


11. REMOVE FRONT WIPER ARM RH
  1. Remove the nut, wiper arm and blade.


12. REMOVE HOOD TO COWL TOP SEAL

  1. E156189
    Using a clip remover, detach the 12 clips, 4 clamps and remove the hood to cowl top seal.


13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E156188
    Remove the washer hose.

  1. E156191
    Remove the 2 clips.

  1. Detach the 17 claws and remove the cowl top ventilator louver sub-assembly.


14. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. A174148
    Remove the 3 bolts and screw.

  1. Loosen the clip and remove the splash shield.


15. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Remove the 3 bolts and screw.

  1. Loosen the clip and remove the splash shield.


16. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and under cover.


17. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and under cover.


18. REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483
  1. Remove the 4 bolts and oil pan protector.


19. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator reservoir cap to drain the coolant in the radiator.

  1. Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

    A174741E01

  1. Tighten the radiator drain cock plug by hand.

  1. A177208
    Tighten the oil filter bracket drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


20. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A177219
    Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }


21. REMOVE NO. 3 ENGINE ROOM WIRE
  1. Disconnect the 4 wire harness clamps.

  1. Remove the 2 nuts and No. 3 engine room wire.

    A174837


22. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

  1. A174701
    Remove the 2 nuts and No. 1 engine cover.


23. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A174698
    Loosen the hose clamp.

  1. Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.

  1. Detach the 4 clamps and remove the air cleaner cap.


24. REMOVE AIR CLEANER FILTER ELEMENT

25. REMOVE AIR CLEANER CASE

  1. A174700
    Using a clip remover, detach the wire harness clamp.

  1. Remove the 3 bolts and air cleaner case.


26. REMOVE NO. 1 AIR CLEANER HOSE

  1. A174699
    Loosen the hose clamp and remove the No. 1 air cleaner hose.


27. REMOVE INTAKE AIR CONNECTOR

  1. A174749E01
    w/o Viscous Heater:

    1. Disconnect the connector from the water temperature sensor.

    2. Using a clip remover, detach the 3 wire harness clamps.

  1. w/ Viscous Heater:

    1. Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.

    2. Using a clip remover, detach the 3 wire harness clamps.

  1. A174710
    Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.


28. REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A177428
    Insert a screwdriver between the reservoir and oil reservoir bracket, push the claw, and then disconnect the reservoir by pulling it upwards.


29. REMOVE NO. 1 OIL RESERVOIR BRACKET

  1. A184319
    Remove the 2 bolts and bracket.


30. REMOVE RADIATOR RESERVOIR ASSEMBLY

  1. A174735
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and radiator reservoir.


31. REMOVE VANE PUMP ASSEMBLY

  1. C172309
    Remove the 2 nuts and vane pump.

  1. Remove the O-ring from the vane pump.


32. DISCONNECT NO. 1 RADIATOR HOSE

33. DISCONNECT NO. 2 RADIATOR HOSE

34. REMOVE V-RIBBED BELT (w/ Viscous Heater)

  1. A174847
    Loosen the lock nut and turn the bolt counterclockwise.

  1. Remove the V-ribbed belt.


35. REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)

  1. A177430
    Remove the bolt, cover, No. 1 idler pulley and collar.


36. REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)

  1. A177431
    Remove the nut and No. 3 idler pulley.


37. REMOVE V-RIBBED BELT

  1. A174849
    Using a wrench to the V-ribbed belt tensioner bracket, turn the wrench clockwise and remove the V-ribbed belt.


38. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Remove the 3 clips and front fender apron seal front RH.


39. REMOVE FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Remove the 4 clips and front fender apron seal rear RH.


40. REMOVE FRONT FENDER APRON SEAL FRONT LH

  1. A176301
    w/o KDSS:
    Remove the 4 clips and front fender apron seal front LH.

  1. A177004
    w/ KDSS:
    Remove the 3 clips and front fender apron seal front LH.


41. REMOVE FRONT FENDER APRON SEAL REAR LH

  1. A177005
    Remove the 4 clips and front fender apron seal rear LH.


42. REMOVE OIL COOLER TUBE (for Automatic Transmission)

  1. C167861
    Disconnect the inlet and outlet No. 1 oil cooler hose.

  1. C175574
    Disconnect the inlet No. 2 and No. 3 oil cooler hoses.

  1. C175575
    Disconnect the inlet No. 4 oil cooler hose.

  1. C167866
    Remove the 2 bolts and transmission oil cooler tube.


43. REMOVE FAN SHROUD WITH FAN

  1. A161930
    Loosen the 4 nuts holding the fluid coupling fan.

  1. A177427
    Remove the 2 bolts holding the fan shroud.

  1. A179253
    Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.


44. REMOVE FAN PULLEY

45. REMOVE FRONT BUMPER WINCH COVER (w/ Winch)

46. REMOVE RADIATOR GRILLE

B180899E01
  1. Put protective tape around the radiator grille.

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille.


47. REMOVE FRONT BUMPER COVER

HINT:
For the front bumper cover with garnish, use the procedures described below.

  1. Put protective tape around the bumper cover.

    B180993E01

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B180994E01

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Detach the 10 claws and remove the bumper cover.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Detach the 10 claws, disconnect the No. 4 engine room wire connector and remove the bumper cover.

    B180995

  1. B181927
    w/ Headlight Cleaner System:
    Disconnect the headlight cleaner hose and remove the bumper cover.


48. REMOVE TRANSMISSION OIL COOLER AIR DUCT (for Automatic Transmission)

  1. A184326
    Remove the 4 bolts and oil cooler air duct.


49. DISCONNECT RADIATOR SIDE DEFLECTOR RH (for Manual Transmission)

  1. A174321
    Using a clip remover, remove the 4 clips, and remove the side deflector.


50. DISCONNECT RADIATOR SIDE DEFLECTOR LH

  1. A174322
    Using a clip remover, remove the 4 clips, and remove the side deflector.


51. REMOVE RADIATOR ASSEMBLY

  1. A174155
    Remove the 4 bolts and radiator.


52. DISCONNECT FRONT DIFFERENTIAL BREATHER TUBE

A177338

53. DISCONNECT FUEL TUBE
  1. Disconnect the 3 fuel tubes from the No. 1 and No. 3 fuel tube clamps.


54. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)

  1. A174703
    Loosen the No. 1 air hose clamp.

  1. A174702
    Loosen the No. 2 air hose clamp.

  1. A174704
    Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

  1. A174705
    Remove the 6 nuts, 2 bolts and intercooler.

  1. Remove the 2 gaskets from the air tube LH and RH.


55. REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

  1. A257026
    Loosen the No. 1 air hose clamp.

  1. Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

  1. A257028
    Remove the 3 nuts, bolt and No. 1 cool air inlet.

  1. Remove the gasket from the air tube RH.


56. REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

  1. A257027
    Loosen the No. 2 air hose clamp.

  1. A257029
    Remove the 3 nuts, bolt and No. 2 cool air inlet.

  1. Remove the gasket from the air tube LH.


57. DISCONNECT WATER HOSE SUB-ASSEMBLY

A174687E01

58. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A174875
    Disconnect the wire harness clamp from the No. 2 engine oil level dipstick guide.

  1. A170321
    Disconnect the ventilation hose from the cylinder head cover RH.

  1. Remove the 2 bolts and No. 2 engine oil level dipstick guide.

  1. Remove the O-ring from the No. 2 engine oil level dipstick guide.


59. REMOVE AIR TUBE SUB-ASSEMBLY RH

A174729
  1. Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


60. REMOVE DIESEL THROTTLE BODY ASSEMBLY RH

A163132
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


61. DRAIN CLUTCH FLUID (for Manual Transmission)

62. REMOVE CLUTCH HOSE (for Manual Transmission)

  1. A177028
    Disconnect the 2 flexible hose tubes from the clutch hose with a 10 mm union nut wrench while holding the flexible hose with a wrench.

    NOTICE:
    1. Do not bend or damage the flexible hose tubes.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tubes from the connecting point.

  1. Remove the 2 clips.

  1. A183845
    Remove the bolt and clutch hose.


63. REMOVE AIR TUBE SUB-ASSEMBLY LH

A174728
  1. Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


64. REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177030
    Using a 10 mm union nut wrench, disconnect the tube connector to flexible hose tube from the clutch tube to release cylinder 2 way.

    NOTICE:
    1. Do not bend or damage the flexible hose tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tube from the connecting point.

  1. A177031
    Remove the 2 bolts and tube connector to flexible hose tube.


65. REMOVE NO. 1 GAS FILTER

  1. A163347
    Disconnect the hose from the intake pipe.

  1. Remove the gas filter.


66. REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

  1. A185151
    for Manual Transmission:

    1. Remove the bolt and disconnect the clutch tube to release cylinder 2 way from the bracket.

  1. A163348
    Remove the 2 bolts and bracket.


67. REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

A163131
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


68. REMOVE NO. 1 AIR HOSE

  1. A177374
    Loosen the hose clamp and remove the No. 1 air hose.


69. REMOVE NO. 3 AIR TUBE

  1. A174751
    Disconnect the wire harness from the clamp.

  1. Remove the nut and ground wire.

  1. A174752
    Remove the bolt and disconnect the wire harness bracket.

  1. A174708
    Loosen the hose clamp and remove the bolt and No. 3 air tube.


70. REMOVE NO. 1 AIR TUBE ASSEMBLY

  1. A174709
    Remove the bolt and No. 1 air tube.

  1. Remove the O-ring.


71. REMOVE NO. 2 AIR HOSE

  1. A177375
    Loosen the hose clamp and remove the No. 2 air hose.


72. REMOVE NO. 4 AIR TUBE

  1. A174690
    Remove the bolt and disconnect the suction hose.

  1. A174706
    Loosen the hose clamp and remove the bolt and No. 4 air tube.


73. REMOVE NO. 2 AIR TUBE ASSEMBLY

  1. A174707
    Remove the bolt and No. 2 air tube.

  1. Remove the O-ring.


74. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174711
    Disconnect the ventilation hose from the oil separator.

  1. Loosen the hose clamp.

  1. Remove the bolt and No. 2 air cleaner pipe.


75. REMOVE NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

  1. E154190
    Remove the bolt and disconnect the discharge hose from the cooler compressor.

  1. Remove the O-ring from the discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.


76. REMOVE SUCTION HOSE SUB-ASSEMBLY

  1. E154191
    Remove the bolt and disconnect the suction hose from the cooler compressor.

  1. Remove the O-ring from the suction hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.


77. REMOVE COOLER COMPRESSOR ASSEMBLY

  1. A174754
    Disconnect the 4 connectors.

  1. Using a clip remover, detach the 3 wire harness clamps.

  1. E154192
    Remove the 4 bolts and cooler compressor.


78. REMOVE NO. 2 INTAKE AIR CONNECTOR PIPE

  1. A174712
    w/ Intercooler:
    Disconnect the vacuum hose.

  1. A174713
    Loosen the hose clamp, and remove the bolt and No. 2 intake air connector pipe.


79. REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

  1. A174689
    Remove the 4 bolts and disconnect the 4 water hose ends, and then remove the heater water pipe.


80. REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174714
    Loosen the hose clamp.

  1. Remove the bolt and No. 1 air cleaner pipe.


81. DISCONNECT FUEL HOSE

A174685E01

82. REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

  1. A174688
    Remove the 2 bolts and disconnect the 2 water hose ends, and then remove the No. 3 water by-pass pipe.


83. REMOVE NO. 4 WATER BY-PASS PIPE

  1. A174691
    w/ EGR System:

    1. Remove the 2 bolts and nut.

    2. Disconnect the 4 water hose ends, and then remove the No. 4 water by-pass pipe.

  1. A174692
    w/o EGR System:

    1. Remove the 2 bolts and nut.

    2. Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.


84. DISCONNECT ENGINE WIRE

  1. LH Side:

    1. A174744
      Disconnect the 4 connectors from the injector driver.

    2. Disconnect the 4 connectors and detach the wire harness holder from the relay block.

    3. Remove the bolt and disconnect the ground wire.

    4. Disconnect the wire harness from the wire harness clamp holder.

    5. A174743E01
      Remove the bolt and disconnect the ground wire from the body panel.

    6. Using a clip remover, detach the ground wire clamp labeled A from the relay block side.

    7. Disconnect the wire harness from the wire harness clamp holder labeled B.

    8. A174745
      Remove the nut and detach the generator positive (+) cable holder from the relay block.

    9. Disconnect the generator positive (+) cable from the 2 clamps.

    10. A174755
      Disconnect the 2 connectors.

    11. Using a clip remover, detach the 3 wire harness clamps.

    12. A174747E01
      for RHD:
      Disconnect the 4 connectors and detach the wire harness tab labeled A from the relay block.

    13. for RHD:
      Disconnect the ECM connector.

    14. for RHD:
      Disconnect the wire harness from the wire harness clamp holder.

    15. A174756E01
      Disconnect the 8 connectors.

    16. Remove the 2 bolts labeled A and disconnect the engine wire protector.

    17. Remove the bolt labeled B and the engine wire harness bracket.

    18. for RHD:
      Disconnect the ECM wire harness from the wire harness clamp holder labeled C.

  1. RH Side:

    1. A179104E01
      for LHD:
      Disconnect the 4 connectors, and detach the wire harness holder labeled A from the relay block.

    2. for LHD:
      Disconnect the ECM connector.

    3. for LHD:
      Disconnect the wire harness from the wire harness clamp holder.

    4. A174750E01
      Disconnect the 7 connectors.

    5. Using a clip remover, detach the wire harness clamp.

    6. Remove the 3 bolts labeled A and disconnect the engine wire protector.

    7. Remove the bolt labeled B and the wire harness bracket.

    8. Remove the nut labeled C and the glow plug wire harness.

    9. A174759
      for RHD:
      Disconnect the wire harness from the wire harness clamp holder.

    10. A174760
      w/ Winch:
      Remove the bolt and disconnect the ground wire.

  1. Rear Side:

    1. A174757E01
      Using a clip remover, detach the wire harness clamp.

    2. Remove the 2 bolts and 2 ground wires labeled C.

    3. Remove the 2 bolts labeled B and disconnect the engine wire harness protector.

    4. Disconnect the 2 common rail connectors.

    5. Remove the nut and disconnect the glow plug wire harness labeled A.


85. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

NOTICE:
A174693
  1. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel pipe ends, cover the fuel pipe ends with plastic bags.
  2. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel supply pump hole, cover the hole with protective tape.

  1. Disconnect the fuel hose from the No. 5 nozzle leakage pipe.

  1. Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the union bolt and gasket.

  1. Remove the bolt, nut and No. 2 fuel pipe.


86. REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes, cover the holes with protective tape.

  1. A185542
    w/ EGR System:

    1. Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the 2 nuts and 2 No. 2 injection pipe clamps.

    3. Remove the No. 6 injection pipe.

  1. A174695
    w/o EGR System:

    1. Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the nut and No. 2 injection pipe clamp.

    3. Remove the bolt and No. 6 injection pipe.


87. REMOVE INJECTION PIPE LH

  1. A174694
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.

  1. A174789
    Using a union nut wrench, remove the 4 injection pipes.

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


88. REMOVE COMMON RAIL ASSEMBLY LH

  1. A176404
    Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the fuel pressure limiter from the common rail. If it is removed, replace the common rail.


89. REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

  1. A174697
    Disconnect the 2 hoses from the fuel pipe.

  1. Remove the bolt and fuel filter to injection pump fuel pipe.


90. DISCONNECT FUEL PUMP MOTOR WIRE

  1. A174792
    Remove the bolt and disconnect the connector from the fuel supply pump.


91. REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

  1. A174696
    Using a union nut wrench, remove the No. 5 injection pipe.

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail hole or injection pump hole, cover the holes with protective tape.


92. REMOVE INJECTION PIPE RH

  1. A174788
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.

  1. A174793
    Using a union nut wrench, remove the 4 injection pipes.

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


93. REMOVE COMMON RAIL ASSEMBLY RH

  1. A176411
    Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the fuel pressure sensor from the common rail. If it is removed, replace the common rail.


94. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174795

95. REMOVE NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174791

96. REMOVE INTAKE PIPE

  1. A174796
    w/ EGR System:
    Remove the 2 nuts, 6 bolts, intake pipe and 2 gaskets.

  1. A180252
    w/o EGR System:
    Remove the 2 nuts, 4 bolts, intake pipe and gasket.


97. DISCONNECT NO. 2 ENGINE WIRE

  1. A174797
    Remove the 3 bolts and using a clip remover, detach the 2 wire harness clamps, and then disconnect the No. 2 engine wire.


98. REMOVE NO. 3 INTAKE MANIFOLD

  1. A174798
    Remove the 16 bolts, No. 3 intake manifold and 2 gaskets.


99. REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR System)

A174799

100. REMOVE EGR PIPE INSULATOR (w/ EGR System)

  1. A174800
    Remove the 2 bolts and EGR pipe insulator.


101. REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

  1. A174801
    Remove the 10 bolts, EGR valve with EGR cooler and 2 gaskets.

  1. A174802
    Disconnect the No. 5 water by-pass hose from the water by-pass outlet.


102. REMOVE EGR COOLER INSULATOR (w/ EGR System)

A174803

103. REMOVE NO. 3 NOZZLE LEAKAGE PIPE

  1. A174804
    Disconnect the No. 1 fuel hose from the fuel cooler.

  1. Remove the union bolt, bolt, No. 3 nozzle leakage pipe and gasket.

    NOTICE:
    After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.


104. REMOVE NO. 4 NOZZLE LEAKAGE PIPE

  1. A174805
    Disconnect the No. 2 fuel hose from the fuel cooler.

  1. Remove the union bolt, bolt, No. 4 nozzle leakage pipe and gasket.

    NOTICE:
    After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.


105. DISCONNECT NO. 6 WATER BY-PASS HOSE

A174806

106. REMOVE FUEL COOLER ASSEMBLY

  1. A176378
    Remove the 2 bolts and fuel cooler.


107. REMOVE NO. 1 WATER BY-PASS PIPE

  1. A174808
    Remove the union bolt, bolt, No. 1 water by-pass pipe and gasket.


108. REMOVE NO. 1 INTAKE MANIFOLD

  1. A174809
    Remove the 9 bolts, No. 1 intake manifold and gasket.


109. REMOVE NO. 2 INTAKE MANIFOLD

  1. A174810
    Remove the 9 bolts, No. 2 intake manifold and gasket.


110. INSTALL NO. 1 AND NO. 2 ENGINE HANGER

  1. A181664E01
    Install the No. 1 and No. 2 engine hangers to the cylinder head RH and LH with the 4 bolts as shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Engine Hanger Part No. 
    Item
    Part No.
    No. 1 engine hanger
    12281-51040
    No. 2 engine hanger
    12282-51040
    Bolt
    91671-80825


111. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
  1. Remove the automatic transmission assembly (Click here).


112. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
  1. Remove the manual transmission unit assembly (Click here).


113. REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177337
    Remove the bolt and tube.


114. REMOVE ENGINE ASSEMBLY

  1. A174842
    Attach an engine sling device and hang the engine with a chain block.

  1. Remove the 4 bolts from the engine mounting RH and LH side.

  1. Lift the engine out of the vehicle carefully.

    NOTICE:
    Make sure the engine is clear of all wiring and hoses.

  1. Place the engine onto a work bench.


115. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

C173317E01
  1. Put matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 8 set bolts, and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


116. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.


117. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. A185177
    Using a wrench, hold the crankshaft.

    NOTICE:
    Do not turn the crankshaft counterclockwise.
    If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (Click here).

    Torque:
    108 N*m{ 1101 kgf*cm , 80 ft.*lbf } or more

  1. A177363
    Remove the 8 bolts.

  1. A177364E01
    Remove the rear drive plate spacer labeled A, drive plate and ring gear labeled B and rear crankshaft balancer weight labeled C.


118. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A185177
    Using a wrench, hold the crankshaft.

    NOTICE:
    Do not turn the crankshaft counterclockwise.
    If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (Click here).

    Torque:
    108 N*m{ 1101 kgf*cm , 80 ft.*lbf } or more

  1. A177365
    Remove the 8 bolts and flywheel.


119. INSTALL ENGINE STAND
  1. Install the engine onto an engine stand with bolts.

  1. Remove the 4 bolts and No. 1 and No. 2 engine hangers.


120. REMOVE FRONT ENGINE MOUNTING INSULATOR RH

A176553
  1. Disconnect the vacuum hose.

  1. Remove the nut and mounting insulator.


121. REMOVE FRONT ENGINE MOUNTING INSULATOR LH

  1. A176552
    Remove the nut and mounting insulator.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →