INSTALLATION
Removal / installation · Vehicles built from Sep 2011
| 1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1) |
Install a new O-ring to the oil control valve.
Apply a light coat of engine oil to the O-ring.
Install the oil control valve with the bolt.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
- NOTICE:
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
- Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
Connect the oil control valve connector.
| 2. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1) |
Install a new O-ring to the oil control valve.
Apply a light coat of engine oil to the O-ring.
Install the oil control valve with the bolt.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
- NOTICE:
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
- Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
Connect the oil control valve connector.
| 3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2) |
Install a new O-ring to the oil control valve.
Apply a light coat of engine oil to the O-ring.
Install the oil control valve with the bolt.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
- NOTICE:
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
- Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
Connect the oil control valve connector.
| 4. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2) |
Install a new O-ring to the oil control valve.
Apply a light coat of engine oil to the O-ring.
Install the oil control valve with the bolt.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
- NOTICE:
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
- Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
- Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
Connect the oil control valve connector.
| 5. INSTALL AIR CLEANER HOSE ASSEMBLY |
Install the air cleaner hose so that the protrusion of the air cleaner cap aligns with the groove of the hose as shown in the illustration.

Text in Illustration *1
Groove
*2
Protrusion
Tighten the 2 clamps.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Connect the vacuum hose.
Connect the No. 2 ventilation hose.
| 6. INSTALL V-BANK COVER SUB-ASSEMBLY |
Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.

Text in Illustration *1
Bracket
*2
Hook
*3
Pin
*4
Grommet
