2011-2013 Land Cruiser · Service Manual Vehicle Exterior

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT REMOTE CONTROL SWITCH ASSEMBLY

  1. B180477
    Connect the remote control switch connector.

  1. B167941
    Turn the engine switch on (IG) and check that the power indicator light illuminates.

  1. Press the remote control switch, and check that the winch operates.

    NOTICE:
    Be careful not to tighten or strain the winch wire.

  1. Turn the engine switch off.


REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


REMOVE UPPER RADIATOR SUPPORT SEAL
  1. for Gasoline Engine:
    Remove the upper radiator support seal (Click here).

  1. for Diesel Engine:
    Remove the upper radiator support seal (Click here).


REMOVE FRONT BUMPER WINCH COVER SUB-ASSEMBLY

REMOVE RADIATOR GRILLE ASSEMBLY

B180899E01
  1. Put protective tape around the radiator grille.

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille.


REMOVE FRONT BUMPER COVER

  1. Put protective tape around the bumper cover.

    B185485E01

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B180994E01

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. Detach the 10 claws.

  1. w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Disconnect the winch control wire connector and remove the bumper cover.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Disconnect the No. 4 engine room wire connector and winch control wire connector and remove the bumper cover.

    B185486


INSPECT OVERHEAT TEMPERATURE INDICATOR

  1. B180478
    Remove the 4 screws and cover.

  1. B180479
    Disconnect the motor relay connector.

  1. B180480
    Remove the 2 nuts.

  1. Pull the bumper side winch control wire out of the bumper.

  1. Connect the bumper side winch control wire connector to the vehicle side winch control wire connector.

  1. Connect the bumper side winch control wire connector to the winch control switch connector.

  1. B167943
    Turn the engine switch on (IG) and check that the overheat temperature indicator light illuminates and the buzzer sounds.

  1. Turn the engine switch off.

  1. Disconnect the bumper side winch control wire connector from the winch control switch connector.

  1. Disconnect the bumper side winch control wire connector from the vehicle side winch control wire connector.

  1. Pass the bumper side winch control wire through the bumper.

  1. B180480
    Install the 2 nuts.

  1. B180479
    Connect the motor relay connector.

  1. B180478
    Install the cover with the 4 screws.


INSTALL FRONT BUMPER COVER
  1. w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Connect the winch control wire connector and attach the 10 claws to install the bumper cover.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Connect the No. 4 engine room wire connector and winch control wire connector, and attach the 10 claws to install the bumper cover.

  1. Install the 3 clips, 4 screws and 4 bolts.

    B185486

  1. Using a T30 "TORX" socket, install the 6 screws.

    B180994E01


INSTALL RADIATOR GRILLE ASSEMBLY

B180899
  1. Attach the 2 clips and 8 claws to install the radiator grille.

  1. Install the 3 screws.


INSTALL FRONT BUMPER WINCH COVER SUB-ASSEMBLY

INSTALL UPPER RADIATOR SUPPORT SEAL
  1. for Gasoline Engine:
    Install the upper radiator support seal (Click here).

  1. for Diesel Engine:
    Install the upper radiator support seal (Click here).


INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.

← PARTS LOCATION (from Sep 2011)ON-VEHICLE INSPECTION (from Jan 2012) →