2011-2013 Land Cruiser · Service Manual Vehicle Exterior

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT REMOTE CONTROL SWITCH ASSEMBLY

  1. B180477
    Connect the remote control switch connector.

  1. B167941
    Turn the engine switch on (IG) and check that the power indicator light illuminates.

  1. Press the remote control switch, and check that the winch operates.

    NOTICE:
    Be careful not to tighten or strain the winch wire.

  1. Turn the engine switch off.


REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


REMOVE UPPER RADIATOR SUPPORT SEAL
(Click here)

REMOVE FRONT BUMPER WINCH COVER SUB-ASSEMBLY

  1. B302213
    Detach the 2 claws.

  1. Detach the 3 guides and remove front bumper winch cover sub-assembly.


REMOVE RADIATOR GRILLE ASSEMBLY

  1. B302174E01
    Put protective tape around the radiator grille assembly.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille assembly.

  1. w/ Wide View Front Monitor System:

    1. Disconnect the connector.


REMOVE FRONT BUMPER COVER

  1. Put protective tape around the bumper cover.

    B302214E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B313279E01

    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. Detach the 10 claws.

    B302215

  1. Disconnect the winch control wire connector and remove the front bumper cover.

  1. w/ Fog Light:
    Disconnect the No. 4 engine room wire connector and remove the front bumper cover.


INSPECT OVERHEAT TEMPERATURE INDICATOR

  1. B180478
    Remove the 4 screws and cover.

  1. B180479
    Disconnect the motor relay connector.

  1. B180480
    Remove the 2 nuts.

  1. Pull the bumper side winch control wire out of the bumper.

  1. Connect the bumper side winch control wire connector to the vehicle side winch control wire connector.

  1. Connect the bumper side winch control wire connector to the winch control switch connector.

  1. B167943
    Turn the engine switch on (IG) and check that the overheat temperature indicator light illuminates and the buzzer sounds.

  1. Turn the engine switch off.

  1. Disconnect the bumper side winch control wire connector from the winch control switch connector.

  1. Disconnect the bumper side winch control wire connector from the vehicle side winch control wire connector.

  1. Pass the bumper side winch control wire through the bumper.

  1. B180480
    Install the 2 nuts.

  1. B180479
    Connect the motor relay connector.

  1. B180478
    Install the cover with the 4 screws.


INSTALL FRONT BUMPER COVER
  1. w/ Fog Light:
    Connect the No. 4 engine room wire connector.

  1. Connect the winch control wire connector and attach the 10 claws to install the front bumper cover.

  1. Install the 3 clips, 4 screws and 4 bolts.

  1. Using a T30 "TORX" socket, install the 6 screws.


INSTALL RADIATOR GRILLE ASSEMBLY
  1. w/ Wide View Front Monitor System:

    1. Connect the connector.

  1. Attach the 2 clips and 8 claws to install the radiator grille assembly.

  1. Install the 3 screws.


INSTALL FRONT BUMPER WINCH COVER SUB-ASSEMBLY

INSTALL UPPER RADIATOR SUPPORT SEAL
  1. for Gasoline Engine:
    Install the upper radiator support seal (Click here).

  1. for Diesel Engine:
    Install the upper radiator support seal (See page ).


INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Push in the clip to install the front fender splash shield sub-assembly RH.

  1. Install the 3 bolts and 2 screws.


INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
  1. Push in the clip to install the front fender splash shield sub-assembly LH.

  1. Install the 3 bolts and screw.

← ON-VEHICLE INSPECTION (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →