2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE VACUUM PUMP ASSEMBLY (w/ Intercooler)

  1. C172878
    Remove the 3 bolts and vacuum pump.

  1. Remove the 2 O-rings.


2. REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A170301
    Remove the 2 bolts and No. 1 engine oil level dipstick guide.

  1. Remove the O-ring from the No. 1 engine oil level dipstick.


3. REMOVE NO. 1 INTAKE AIR CONNECTOR PIPE

  1. A174753
    Disconnect the 4 connectors.

  1. Using a clip remover, detach the 5 wire harness clamps.

  1. A177381
    Loosen the hose clamp, and remove the bolt and No. 1 intake air connector pipe.


4. REMOVE GENERATOR ASSEMBLY

  1. A174761
    Remove the nut and bolt, and disconnect the generator positive (+) cable.

  1. A163035
    Remove the 3 bolts, 2 nuts and generator.


5. REMOVE NO. 2 VENTILATION HOSE

A264021E01
Text in Illustration 
*A
w/ DPF
*B
w/o DPF

6. REMOVE NO. 2 TURBO WATER HOSE

A267247

7. REMOVE BREATHER PLUG RH

  1. A267248
    Disconnect the hose.

  1. Detach the clamp and remove the breather plug RH.


8. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A264022E01
    Remove the 3 bolts and No. 1 exhaust manifold heat insulator.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


9. DISCONNECT NO. 1 OUTLET TURBO OIL HOSE

A267249

10. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

  1. A177401
    Disconnect the water hose.

  1. Remove the 3 bolts, 2 nuts, No. 1 turbo water pipe and gasket.


11. REMOVE NO. 1 TURBOCHARGER STAY

  1. A177403
    Remove the 2 bolts and No. 1 turbocharger stay.


12. REMOVE NO. 1 VENTILATION TUBE SUB-ASSEMBLY

  1. A264023
    Disconnect the hose.

  1. Remove the union bolt, bolt, No. 1 ventilation tube and gasket.


13. REMOVE NO. 1 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD RH

  1. A177405
    Remove the union bolt and gasket, and disconnect the No. 1 inlet turbo oil pipe from the cylinder block.

  1. Remove the 10 nuts, 10 collars and No. 1 turbocharger with exhaust manifold RH.

    A264024E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket.

  1. A264026
    w/ DPF:
    Remove the 4 bolts, No. 1 exhaust manifold pipe and 2 gaskets.

  1. Remove the 2 nuts and bolt, and separate the No. 1 turbocharger and exhaust manifold RH.

    A264025E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket from the No. 1 turbocharger.


14. REMOVE NO. 3 VENTILATION HOSE

A264027E01
Text in Illustration 
*A
w/ DPF
*B
w/o DPF

15. REMOVE BREATHER PLUG LH

  1. A267263E01
    Disconnect the hose.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. w/o DPF:
    Detach the clamp.

  1. Remove the breather plug LH.


16. REMOVE NO. 2 TURBO WATER HOSE

A267250

17. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A264028E01
    Remove the 3 bolts and No. 2 exhaust manifold heat insulator.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


18. REMOVE NO. 3 TURBO WATER PIPE SUB-ASSEMBLY

  1. A177386
    Remove the 2 bolts, union bolt, No. 3 turbo water pipe and gasket.


19. REMOVE FRONT WATER BY-PASS JOINT

  1. A177435
    Remove the front water by-pass joint and gasket.


20. REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

  1. A267251
    Disconnect the water hose.

  1. Remove the union bolt, bolt, No. 2 turbo water pipe and gasket.


21. DISCONNECT NO. 2 OUTLET TURBO OIL HOSE

A267252

22. REMOVE NO. 2 TURBOCHARGER STAY

  1. A267253
    Remove the 2 bolts and No. 2 turbocharger stay.


23. REMOVE NO. 2 VENTILATION TUBE SUB-ASSEMBLY

  1. Disconnect the hose.

    A264029E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the union bolt, bolt, No. 2 ventilation tube and gasket.


24. REMOVE NO. 2 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD LH

  1. A179471
    Disconnect the 2 connectors from the turbocharger.

  1. A177391
    Remove the union bolt and gasket, and disconnect the No. 2 inlet turbo oil pipe from the No. 1 oil pan.

  1. Remove the 10 nuts, 10 collars and No. 2 turbocharger with exhaust manifold LH.

    A264030E01

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket.

  1. A264032
    w/ DPF:
    Remove the 4 bolts, No. 2 exhaust manifold pipe and 2 gaskets.

  1. A264031E01
    Remove the 3 nuts, and separate the No. 2 turbocharger and exhaust manifold LH.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the gasket from the turbocharger.


25. REMOVE VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)

E154426
  1. Disconnect the connector and detach the clamp.

  1. Using pliers, grip the claws of the clips and slide the 2 clips.

  1. Disconnect the 2 heater hoses.

  1. Remove the 2 bolts and heater assembly.


26. REMOVE NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

  1. A177432
    Remove the bolt and No. 1 idler pulley bracket.


27. REMOVE WATER INLET

  1. A174815
    Disconnect the No. 2 oil cooler hose from the water pump and clamp.

  1. A174816
    Remove the 4 bolts and water inlet.


28. REMOVE THERMOSTAT
  1. Remove the thermostat.

  1. Remove the gasket from the thermostat.


29. REMOVE TIMING GEAR COVER INSULATOR (w/ Intercooler)

  1. A174822
    w/o Viscous Heater:
    Remove the 2 bolts and timing gear cover insulator.

  1. A174823
    w/ Viscous Heater:
    Remove the timing gear cover insulator.


30. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A177437
    Remove the 3 bolts and V-ribbed belt tensioner bracket.

  1. A174864
    Remove the bolt and No. 1 idler pulley.

  1. A177414
    Remove the 5 bolts and V-ribbed belt tensioner.


31. REMOVE STARTER ASSEMBLY

  1. A269804
    Detach the harness clamp and disconnect the wire harness.

  1. Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.

  1. A269805
    Disconnect the 2 starter hoses.

  1. A269806
    Remove the 2 bolts and starter.


32. REMOVE STARTER HOSE BRACKET

  1. A267278
    Remove the 2 bolts and starter hose bracket.


33. DISCONNECT INLET WATER HOSE

A164893

34. REMOVE DIESEL ENGINE COOLANT TEMPERATURE SENSOR

A175726
  1. Disconnect the sensor connector.

  1. Using a 19 mm deep socket wrench, remove the sensor and gasket.


35. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET

  1. A164465
    Remove the 2 bolts and No. 2 intercooler support bracket.


36. REMOVE WATER OUTLET

  1. A164484
    Remove the 2 bolts and gasket and disconnect the water outlet from the No. 2 water hose joint.


37. REMOVE WATER OUTLET PIPE

  1. A177325
    Remove the 4 bolts, water outlet pipe and 2 gaskets.


38. SEPARATE NO. 1 AND NO. 2 WATER OUTLET PIPES AND WATER BY-PASS OUTLET

  1. A177326
    Remove the 2 bolts and No. 1 water outlet pipe from the No. 2 water outlet pipe.

  1. A177327
    Disconnect the No. 2 water outlet pipe from the No. 1 water hose joint.

  1. A177328
    Disconnect the water by-pass outlet from the No. 1 water hose joint.


39. REMOVE CLUTCH FLEXIBLE HOSE BRACKET (for Manual Transmission)

  1. A177336
    Remove the 2 bolts and clutch flexible hose bracket.


40. REMOVE NO. 1 GLOW PLUG CONNECTOR
  1. Remove the 2 screw grommets and 2 nuts, and disconnect the 2 wire harnesses.

  1. A269587E01
    Remove the 8 screw grommets, 8 nuts and 2 glow plug connectors.
    Text in Illustration 
    *a
    RH
    *b
    LH


41. REMOVE GLOW PLUG ASSEMBLY

  1. A269588E01
    Using a 10 mm deep socket wrench, remove the 8 glow plugs.
    Text in Illustration 
    *a
    RH
    *b
    LH

    HINT:
    Before removing the glow plugs, thoroughly clean off all dirt, sand, etc.


42. REMOVE FUEL PUMP MOTOR WIRE

  1. A174811
    Disconnect the 2 connectors and remove the bolt and fuel pump motor wire.


43. REMOVE NO. 2 IDLER PULLEY (w/ Viscous Heater)

  1. A177433
    Remove the bolt, cover, No. 2 idler pulley and collar.


44. REMOVE NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

  1. E154425
    Remove the 3 bolts and idler pulley bracket.


45. REMOVE FAN BRACKET SUB-ASSEMBLY

  1. A174820
    Remove the 4 bolts and fan bracket.


46. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/o DPF)

  1. A174969
    Disconnect the 2 vacuum hoses.

  1. Remove the bolt and vacuum switching valve.


47. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/o DPF)

  1. A264755
    w/ Intercooler:
    Disconnect the 2 vacuum hoses.

  1. A264102
    Remove the 3 bolts and vacuum transmitting pipe.


48. REMOVE CYLINDER HEAD COVER SILENCER RH (w/o DPF)

  1. A174974
    w/ Intercooler:
    Remove the 3 bolts and cylinder head cover silencer RH.


49. REMOVE CYLINDER HEAD COVER SILENCER LH (w/o DPF)

  1. A174975
    w/ Intercooler:
    Remove the 3 bolts and cylinder head cover silencer LH.


50. REMOVE REAR CYLINDER HEAD PLATE RH (w/o EGR System)

  1. A179124
    Remove the 2 bolts, rear cylinder head plate RH and gasket.


51. REMOVE REAR CYLINDER HEAD PLATE LH (w/o EGR System)

  1. A179125
    Remove the 2 bolts, rear cylinder head plate LH and gasket.


52. REMOVE NO. 1 INTAKE AIR CONNECTOR BRACKET

  1. A177073
    Remove the 2 bolts and No. 1 intake air connector bracket.


53. REMOVE AIR TUBE SUPPORT

  1. A177074
    Remove the 2 bolts and air tube support.


54. REMOVE NO. 1 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A177081
    Remove the union bolt, bolt, No. 1 water by-pass pipe and gasket.


55. REMOVE NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A177079
    Disconnect the vacuum hose.

  1. Remove the 2 bolts and No. 4 vacuum transmitting pipe.


56. REMOVE ENGINE MOUNTING BRACKET RH

  1. A177083
    Remove the 4 bolts and engine mounting bracket RH.


57. REMOVE NO. 1 CYLINDER BLOCK INSULATOR

A177085

58. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET

  1. A179111
    Detach the 2 wire harness clamps.

  1. A177076
    Remove the bolt and No. 2 intake air connector bracket.


59. REMOVE TURBOCHARGER WIRE

  1. A177078
    Detach the 3 wire harness clamps.

  1. Remove the 2 bolts and turbocharger wire.


60. REMOVE NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

  1. A177080
    w/ Intercooler:
    Disconnect the vacuum hose.

  1. Remove the 2 bolts and No. 3 vacuum transmitting pipe.


61. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A177082
    Remove the union bolt, 2 bolts, No. 2 water by-pass pipe and gasket.


62. REMOVE ENGINE MOUNTING BRACKET LH

  1. A177084
    Remove the 4 bolts and engine mounting bracket LH.


63. REMOVE NO. 2 CYLINDER BLOCK INSULATOR

A177086

64. REMOVE OIL TANK BRACKET

  1. A177217
    Remove the bolt and oil tank bracket.


65. REMOVE NO. 1 INTERCOOLER SUPPORT BRACKET

  1. A164464
    Remove the 2 bolts and No. 1 intercooler support bracket.


66. REMOVE NO. 3 ENGINE HANGER

  1. A164466
    Remove the 2 bolts and No. 3 engine hanger.


67. REMOVE OIL FILTER BRACKET DRAIN COCK ASSEMBLY

  1. A177208
    Remove the oil filter drain cock plug.

  1. A177209
    Remove the oil filter drain cock body.

    HINT:
    If the drain cock is deformed or clogged, replace or repair it.


68. REMOVE OIL PRESSURE REGULATOR ASSEMBLY

  1. A177215
    Using a 26 mm wrench, remove the oil pressure regulator and gasket.

  1. Remove the O-ring from the oil pressure regulator body.

  1. Hold the oil pressure regulator body in a vise between aluminum plates.

    NOTICE:
    Be careful not to damage the oil pressure regulator body.

  1. A177216E01
    Using a 10 mm hexagon wrench, remove the oil pump relief valve plug labeled A and gasket.

    CAUTION:
    When removing the plug, be careful as the spring will be jumped out.

  1. Remove the 2 springs labeled B.

  1. Remove the oil pump relief valve labeled C.


69. REMOVE STIFFENER INSULATOR RH (w/ Intercooler)

  1. A170322
    Remove the 2 bolts and stiffener insulator RH.


70. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A164915E02
    Align the timing mark of the crankshaft pulley and the chain cover and compressor bracket.
    Text in Illustration 
    *1
    Timing Mark


71. REMOVE COMPRESSOR BRACKET

  1. A177077
    Remove the bolt and compressor bracket.


72. REMOVE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (w/ DPF)

  1. A271245E01
    Disconnect the 2 exhaust fuel addition injector connectors.
    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2

  1. A271247E01
    Remove the 2 bolts, 2 washers and 2 nozzle holder clamps.
    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2
    *1
    Washer
    *2
    Nozzle Holder Clamp

  1. Remove the 2 exhaust fuel addition injectors and 2 gaskets.


73. REMOVE FUEL INJECTOR SEAL (w/ DPF)

  1. A201784E01
    Remove the 2 fuel injector seals.
    Text in Illustration 
    *1
    Fuel Injector Seal


74. REPLACE FLYWHEEL RING GEAR

CAUTION:
A174778E01
When torching the flywheel:
  1. Wear protective gloves.
  2. Be careful as the flywheel is hot.

HINT:
If the flywheel ring gear is deformed or the gear teeth are damaged, replace it.

  1. Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

  1. Install 8 10 mm x 1.25 pitch bolts with a length of 70 mm or more to the flywheel.

  1. Uniformly tighten the 8 bolts in the order shown in the illustration.

  1. Remove the ring gear from the flywheel.

  1. A182763E02
    Using a torch, heat a new ring gear evenly to approximately 200°C (392°F).
    Text in Illustration 
    *a
    No Clearance

    NOTICE:
    Be careful not to overheat the ring gear.

  1. Using a brass bar, tap the ring gear onto the flywheel with its chamfered gear teeth facing the block.

    NOTICE:
    1. Make sure to press in the ring gear until the ring gear contacts the flywheel, as shown in A in the illustration.
    2. After installing, allow the ring gear to cool before handling.


75. REPLACE FLYWHEEL STRAIGHT PIN

HINT:
It is not necessary to remove the straight pin unless it is being replaced.

  1. Replace the flywheel straight pin.

← REMOVAL (Sep 2011 – Dec 2011)DISASSEMBLY (Sep 2011 – Dec 2011) →