2011-2013 Land Cruiser · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built from Sep 2011


1. DRAIN CLUTCH FLUID

2. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

B292994E01
  1. Put protective tape around the No. 2 instrument panel finish panel cushion.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.


3. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

B292995
  1. Remove the clip and screw.

  1. Detach the 8 claws.

  1. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.


4. REMOVE INSTRUMENT SIDE PANEL LH

E154740E06
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


7. REMOVE FRONT DOOR SCUFF PLATE LH

B181682
  1. Detach the 7 claws and 4 clips, and remove the scuff plate.


8. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


9. REMOVE COWL SIDE TRIM BOARD LH

B181911
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


11. REMOVE NO. 1 SWITCH HOLE BASE

B180298
  1. Detach the 4 claws.

  1. Disconnect the connectors and remove the No. 1 switch hole cover.


12. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


13. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299
  1. Detach the 2 claws and disconnect the DLC3.

  1. Remove the 5 bolts and lower instrument panel.


14. REMOVE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

  1. C173731
    Remove the 3 bolts.

  1. C173730
    Disconnect the 9 ECU connectors and remove the ECU.


15. DISCONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE AND CLUTCH RESERVOIR TUBE

C172961
  1. Using a union nut wrench, disconnect the flexible hose tube.

    HINT:
    Use a container to catch the fluid.

  1. Disconnect the clutch reservoir tube.


16. REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY WITH CLUTCH MASTER CYLINDER
  1. Disconnect the clutch start switch connector.

  1. w/ Cruise Control System:
    Disconnect the clutch switch connector.

  1. C172960
    Remove the 2 nuts, bolt and clutch pedal support with clutch master cylinder.


17. REMOVE CLUTCH RESERVOIR HOSE

C173228
  1. Using pliers, grip the claws of the clip, slide the 2 clips and remove the clutch reservoir hose.

    HINT:
    Use a container to catch the fluid.


18. REMOVE CLUTCH MASTER CYLINDER TO WAY TUBE

C173226
  1. Using a union nut wrench, remove the tube.

    HINT:
    Use a container to catch the fluid.


19. REMOVE CLUTCH START SWITCH ASSEMBLY

  1. C173223
    Remove the 2 nuts and clutch start switch.


20. REMOVE CLUTCH MASTER CYLINDER ASSEMBLY

  1. C173225
    Remove the clip, wave washer and clevis pin.

  1. C173224
    Remove the 2 bolts and clutch master cylinder.

← COMPONENTS (from Sep 2011)DISASSEMBLY (from Sep 2011) →