2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LHD and RHD.
  2. The procedures listed below are for the LHD.


1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
  1. Remove the rear No. 1 seat assembly (Click here).


2. REMOVE SEAT ADJUSTER BOLT COVER

B184012
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B184013
  1. Remove the screw and release handle.


4. REMOVE REAR NO. 1 SEAT RECLINING COVER LH

B184014E01
  1. Remove the 2 screws.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cover.


5. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

B184015
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


6. REMOVE UPPER SEAT TRACK RAIL COVER LH

B181222
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


7. REMOVE UPPER SEAT TRACK RAIL COVER RH

B184035
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER

  1. B181224
    Remove the 4 screws and detach the 4 claws.

  1. B184044
    Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.


9. REMOVE REAR NO. 2 SEAT PROTECTOR

  1. B184016
    w/ Rear Seat Side Airbag:
    Detach the claw and remove the wire harness connector.

  1. w/ Seat Heater System:
    Detach the claw and remove the wire harness connector.

  1. B182595
    Using a clip remover, remove the clip.

  1. Detach the claw and remove the seat protector from the seat hinge.

  1. Detach the 2 claws, open the protector and remove wire harness.


10. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

  1. B184045
    w/ Rear Seat Side Airbag:
    Detach the wire harness clamp.

  1. w/ Seat Heater System:
    Detach the wire harness clamp.

  1. Remove the 2 nuts and hinge.

  1. B181176
    Detach the cable clamp and disconnect the cable.


11. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B184017
  1. Remove the 2 nuts and hinge.


12. REMOVE SEAT BELT ANCHOR COVER CAP

  1. B181227
    Detach the claw and open the cap.

  1. B181228
    Remove the screw and anchor cover cap.


13. REMOVE REAR SEATBACK STAY COVER LH

B181226
  1. Remove the screw.

  1. Detach the 2 claws and remove the cover.


14. REMOVE REAR UNDER SIDE COVER LH

  1. B181229
    Detach the 10 claws.

  1. B181230
    Remove the 5 screws.

  1. Detach the 2 clips and 2 claws, and remove the cover.


15. REMOVE REAR SEAT CUSHION COVER RH

B181231
  1. Remove the 4 screws.

  1. Detach the 2 claws and remove the cover.


16. REMOVE REAR SEAT UNDER TRAY COVER LH

B181181
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B184531E01
  1. Remove the bolt and belt.

    HINT:
    The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.


18. REMOVE SEAT CUSHION COVER WITH PAD
  1. w/ Rear Seat Side Airbag:

    1. Detach the side airbag wire harness clamps.

    2. Remove the side airbag wire harness through the hole in the seat cushion.

  1. w/ Seat Heater System:

    1. B182596
      Disconnect the 2 seat heater connectors.

    2. B182597
      Remove the seatback heater wire harness through the hole in the seat cushion.

  1. Remove the seat cushion cover with pad.


19. REMOVE REAR SEATBACK COVER

B181188E01
  1. Using a screwdriver, detach the 4 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


20. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH

B181241
  1. w/ Center Armrest:

    1. Detach the 2 claws on the top of the board.

    2. Pull up the board to detach the 2 claws on the bottom of the board and remove it.

  1. B181240
    w/o Center Armrest:

    1. Detach the 3 claws on the top of the board.

    2. Pull up the board to detach the 3 claws on the bottom of the board and remove it.


21. REMOVE REAR SEAT HEADREST ASSEMBLY

22. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B181190
  1. w/ Center Armrest:
    Detach the 4 claws and remove the 2 supports.

  1. B181243
    w/o Center Armrest:
    Detach the 8 claws and remove the 4 supports.


23. REMOVE SHOULDER BELT ANCHOR COVER

B181238E01
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


24. REMOVE REAR SEAT BELT HOLE COVER LH

B181239
  1. Remove the screw.

  1. Detach the 4 claws and remove the cover.


25. REMOVE SEATBACK COVER WITH PAD

  1. B262667
    w/ Center Armrest:
    Remove the hog rings.

  1. B262668
    w/o Center Armrest:
    Remove the hog rings.

  1. w/ Rear Seat Side Airbag:

    1. B184020
      Remove the cap nut and seatback cover bracket from the seat frame.

    2. Remove the side airbag wire harness through the hole in the seatback.

  1. w/ Seat Heater System:

    1. B182598E01
      Cut the cable tie and disconnect the seatback heater wire harness.

    2. B182638
      Remove the seatback heater wire harness through the hole in the seatback.

  1. B181245
    w/ Center Armrest:
    Pull the seat belt into the inside of the seat.

  1. B181248
    w/o Center Armrest:
    Pull the seat belt into the inside of the seat.

  1. Remove the seatback cover with pad.


26. REMOVE REAR SEAT BACK HINGE COVER LH

B181237
  1. Remove the screw.

  1. Detach the claw and remove the cover.


27. REMOVE REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH

B181791
  1. Remove the 4 screws.

  1. Detach the 4 claws and remove the cover.


28. REMOVE REAR SEAT SHOULDER BELT HOLE COVER

B185854
  1. Using a screwdriver, detach the 3 claws and remove the shoulder belt hole cover.


29. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B185876
  1. Remove the 3 nuts and belt sensor.

  1. Remove the nut and then remove the outer belt.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →