C1622 Open or Short Circuit in Back Camera Signal
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1622 |
An open or short in the rear television camera signal circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When "System initializing" is displayed on the parking assist ECU after the battery terminal disconnected, correct the steering angle neutral point (Click here).
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/ Side Monitor System) may be needed (Click here).
- When "System initializing" is displayed on the parking assist ECU after the battery terminal disconnected, correct the steering angle neutral point (Click here).
| 1. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA AND BODY GROUND) |
Disconnect the F75 and F76 parking assist ECU connectors.
Disconnect the S5 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F76-38 (CV-) - S5-1 (CV-)
Always
Below 1 Ω
F76-15 (CV+) - S5-2 (CV+)
Always
Below 1 Ω
F76-14 (CB+) - S5-4 (CB+)
Always
Below 1 Ω
F76-37 (CGND) - S5-3 (CGND)
Always
Below 1 Ω
F75-4 (GND1) - Body ground
Always
Below 1 Ω
F76-38 (CV-) - Body ground
Always
10 kΩ or higher
F76-15 (CV+) - Body ground
Always
10 kΩ or higher
F76-14 (CB+) - Body ground
Always
10 kΩ or higher
F76-37 (CGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK PARKING ASSIST ECU (CB+, CGND) |
Reconnect the F75 and F76 parking assist ECU connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F76-37 (CGND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
F76-14 (CB+) - F76-37 (CGND)
Engine switch on (IG), shift lever in R
5.5 to 7.05 V
| *a |
Component with harness connected (Parking Assist ECU) |
|
|
||||
| OK | |
| 3. CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND) |
Reconnect the S5 rear television camera assembly connector.


Text in Illustration *a
Component with harness connected
(Parking Assist ECU)
*b
Waveform A
*c
Waveform B
*d
Synchronization Signal
*e
Video Waveform
-
-
Check the waveform of the rear television camera assembly using an oscilloscope.
- HINT:
- A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.
- The video waveform changes according to the image sent by the rear television camera assembly.
- A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.
Item
Content
Terminal No. (Symbol)
F76-15 (CV+) - F76-37 (CGND)
Tool Setting
200 mV/DIV., 50 μsec./DIV.
Condition
- Waveform A: Engine switch on (IG), shift lever in R and camera lens is not covered, displaying an image
- Waveform B: Engine switch on (IG), shift lever in R and camera lens is covered, blacking out the screen
- OK:
- Waveform is as shown in the illustration.
|
|
||||
| OK | ||
| ||
