2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK PARK ASSIST ECU (w/ Parking Assist Monitor System)
E132051E06
  1. Disconnect the F43 and F44 ECU connectors.

  2. Measure the voltage and resistance according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F43-6 (+B) - F43-4 (GND1)
    L - W-B
    Power source signal
    Always
    11 to 14 V
    F43-1 (IG) - F43-4 (GND1)
    G - W-B
    IG power source signal
    Engine switch on (IG)
    11 to 14 V
    F43-1 (IG) - F43-4 (GND1)
    G - W-B
    IG power source signal
    Engine switch off
    Below 1 V
    F43-14 (ACC) - F43-4 (GND1)
    GR - W-B
    ACC power source signal
    Engine switch on (ACC)
    11 to 14 V
    F43-14 (ACC) - F43-4 (GND1)
    GR - W-B
    ACC power source signal
    Engine switch off
    Below 1 V
    F44-6 (CSSW) - F43-4 (GND1)
    Y - W-B
    Clearance sonar main switch power source signal
    Engine switch on (IG),
    clearance sonar main switch on
    11 to 14 V
    F44-6 (CSSW) - F43-4 (GND1)
    Y - W-B
    Clearance sonar main switch power source signal
    Engine switch on (IG),
    clearance sonar main switch off
    Below 1 V
    F43-4 (GND1) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 Ω

  3. Reconnect the F43 and F44 ECU connectors.

  4. Measure the voltage and waveform according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F44-28 (BOR) - F44-29 (E2)
    R - GR
    Rear sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    7.2 to 8.8 V
    F44-28 (BOR) - F44-29 (E2)
    R - GR
    Rear sensor circuit power source
    Engine switch off
    Below 1 V
    F44-33 (SOF) - F44-32 (E1)
    LG - R
    Front sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    Waveform 1
    F44-25 (BBZ) - F43-4 (GND1)
    G - W-B
    No. 1 clearance warning buzzer signal
    Engine switch on (IG)
    7.2 to 8.8 V
    F44-25 (BBZ) - F43-4 (GND1)
    G - W-B
    No. 1 clearance warning buzzer signal
    Engine switch off
    Below 1 V
    F44-9 (EF) - F43-4 (GND1)
    L - W-B
    No. 1 clearance warning buzzer signal
    Buzzer sounding
    Waveform 2
    F44-31 (BOF) - F44-32 (E1)
    GR - R
    Front sensor circuit power source
    Engine switch off
    Below 1 V
    F44-31 (BOF) - F44-32 (E1)
    GR - R
    Front sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    7.2 to 8.8 V
    F44-30 (SOR) - F44-29 (E2)
    LG - GR
    Rear sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    Waveform 1

  5. E133127E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. F44-33 (SOF) - F44-32 (E1)
    2. F44-30 (SOR) - F44-29 (E2)
    Tool Setting
    2 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), clearance sonar main switch on

  6. E051095E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F44-9 (EF) - F43-4 (GND1)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), shift lever moved to R


CHECK CLEARANCE WARNING ECU (w/o Parking Assist Monitor System)
E132050E03
  1. Disconnect the F12 ECU connector.

  2. Measure the voltage and resistance according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F12-15 (IG) - F12-17 (GND1)
    G - W-B
    IG power source signal
    Engine switch on (IG)
    11 to 14 V
    F12-15 (IG) - F12-17 (GND1)
    G - W-B
    IG power source signal
    Engine switch off
    Below 1 V
    F12-12 (CSSW) - F12-17 (GND1)
    Y - W-B
    Clearance sonar main switch power source signal
    Engine switch on (IG),
    clearance sonar main switch on
    11 to 14 V
    F12-12 (CSSW) - F12-17 (GND1)
    Y - W-B
    Clearance sonar main switch power source signal
    Engine switch on (IG),
    clearance sonar main switch off
    Below 1 V
    F12-17 (GND1) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 Ω

  3. Reconnect the F12 ECU connector.

  4. Measure the voltage and waveform according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F12-10 (BBZ) - F12-11 (EF)
    G - L
    No. 1 clearance warning buzzer signal
    Buzzer not sounding
    Below 1 V
    F12-10 (BBZ) - F12-11 (EF)
    G - L
    No. 1 clearance warning buzzer signal
    Buzzer sounding
    Waveform 1
    F12-21 (BOF) - F12-19 (E1)
    GR - R
    No. 1 ultrasonic sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    7.2 to 8.8 V
    F12-21 (BOF) - F12-19 (E1)
    GR - R
    No. 1 ultrasonic sensor circuit power source
    Engine switch off
    Below 1 V
    F12-9 (SOF) - F12-19 (E1)
    LG - R
    No. 1 ultrasonic sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    Waveform 2
    F12-7 (BOR) - F12-18 (E2)
    R - GR
    Rear ultrasonic sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    7.2 to 8.8 V
    F12-7 (BOR) - F12-18 (E2)
    R - GR
    Rear ultrasonic sensor circuit power source
    Engine switch off
    Below 1 V
    F12-24 (SOR) - F12-18 (E2)
    LG - GR
    Rear ultrasonic sensor circuit power source
    Engine switch on (IG), clearance sonar main switch on
    Waveform 2

  5. E051095E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F12-10 (BBZ) - F12-11 (EF)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), shift lever moved to R

    NOTICE:
    The waveform amplitude varies depending on the volume setting.

  6. E133127E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. F12-9 (SOF) - F12-19 (E1)
    2. F12-24 (SOR) - F12-18 (E2)
    Tool Setting
    2 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), clearance sonar main switch on

← PROBLEM SYMPTOMS TABLE (from Jan 2012)TERMINALS OF ECU (from Jan 2012) →