2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK PARK ASSIST ECU (w/ Side Monitor System)
E245334E03
  1. Disconnect the F75 and F76 parking assist ECU connectors.

  2. Measure the voltage and resistance according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F75-1 (+B) - F75-4 (GND1)
    L - W-B
    Power source signal
    Always
    11 to 14 V
    F75-4 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F76-25 (CSSW) - F75-4 (GND1)
    Y - W-B
    back sonar or clearance sonar switch assembly power source signal
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    11 to 14 V
    Engine switch on (IG), back sonar or clearance sonar switch assembly off
    Below 1 V
    F75-8 (IG) - F75-4 (GND1)
    G - W-B
    IG power source signal
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    F75-9 (ACC) - F75-4 (GND1)
    GR - W-B
    ACC power source signal
    Engine switch on (ACC)
    11 to 14 V
    Engine switch off
    Below 1 V

  3. Reconnect the F75 and F76 parking assist ECU connectors.

  4. Measure the voltage and waveform according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F76-3 (LIN2) - F76-4 (CSG2)
    LG - GR
    Rear sensor circuit power source
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    Waveform 1
    F76-5 (CSB1) - F76-6 (CSG1)
    GR - R
    Front sensor circuit power source
    Engine switch off
    Below 1 V
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    7.2 to 8.8 V
    F75-6 (EF) - F75-7 (BBZ)
    L - G
    No. 1 clearance warning buzzer signal
    Buzzer does not sound
    Below 1 V
    Buzzer sounding
    Waveform 2
    F76-20 (CSB2) - F76-4 (CSG2)
    R - GR
    Rear sensor circuit power source
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    7.2 to 8.8 V
    Engine switch off
    Below 1 V
    F76-23 (LIN1) - F76-6 (CSG1)
    LG - R
    Front sensor circuit power source
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    Waveform 1

  5. E133127E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. F76-3 (LIN2) - F76-4 (CSG2)
    2. F76-23 (LIN1) - F76-6 (CSG1)
    Tool Setting
    2 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), back sonar or clearance sonar switch assembly on

  6. E051095E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F75-6 (EF) - F75-7 (BBZ)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), shift lever moved to R

    NOTICE:
    The waveform amplitude varies depending on the volume setting.


CHECK CLEARANCE WARNING ECU ASSEMBLY (w/o Side Monitor System)
E132050E06
  1. Disconnect the F12 clearance warning ECU assembly connector.

  2. Measure the voltage and resistance according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F12-12 (CSSW) - F12-17 (GND1)
    Y - W-B
    back sonar or clearance sonar switch assembly power source signal
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    11 to 14 V
    Engine switch on (IG), back sonar or clearance sonar switch assembly off
    Below 1 V
    F12-15 (IG) - F12-17 (GND1)
    G - W-B
    IG power source signal
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    F12-17 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the F12 clearance warning ECU assembly connector.

  4. Measure the voltage and waveform according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F12-7 (CSB2) - F12-18 (CSG2)
    R - GR
    Rear sensor circuit power source
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    7.2 to 8.8 V
    Engine switch off
    Below 1 V
    F12-9 (LIN1) - F12-19 (CSG1)
    LG - R
    Front sensor circuit power source
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    Waveform 1
    F12-10 (BBZ) - F12-11 (EF)
    G - L
    No. 1 clearance warning buzzer signal
    Buzzer not sounding
    Below 1 V
    Buzzer sounding
    Waveform 2
    F12-21 (CSB1) - F12-9 (LIN1)
    GR - LG
    Front sensor circuit power source
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    7.2 to 8.8 V
    Engine switch off
    Below 1 V
    F12-24 (LIN2) - F12-18 (CSG2)
    LG - GR
    Rear sensor circuit power source
    Engine switch on (IG), back sonar or clearance sonar switch assembly on
    Waveform 1

  5. E133127E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. F12-9 (LIN1) - F12-19 (CSG1)
    2. F12-24 (LIN2) - F12-18 (CSG2)
    Tool Setting
    2 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), back sonar or clearance sonar switch assembly on

  6. E051095E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F12-10 (BBZ) - F12-11 (EF)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine switch on (IG), shift lever moved to R

    NOTICE:
    The waveform amplitude varies depending on the volume setting.

← TERMINALS OF ECU (Sep 2011 – Dec 2011)DTC CHECK / CLEAR (from Sep 2011) →