2011-2013 Land Cruiser · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE NO. 4 ENGINE ROOM WIRE

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Remove the No. 4 engine room wire.

    1. Disconnect the 2 connectors.

    2. Detach the 9 clamps and remove the engine room wire.

      B182885

  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Remove the No. 4 engine room wire.

    1. Disconnect the 4 connectors.

    2. Detach the 9 clamps and remove the engine room wire.

      B180531

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Remove the No. 4 engine room wire.

    1. Disconnect the 2 connectors.

    2. Detach the 9 clamps and remove the engine room wire.

      B185492


2. REMOVE NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to remove the No. 1 ultrasonic sensor on the other side.

  1. E156305
    While pushing down on the lever with a finger to release the one claw, detach the claw on the other side to remove the ultrasonic sensor.

    HINT:
    The type of claw on the top and bottom of the sensor are different. Observe the claws carefully before removing the sensor.


3. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to remove the No. 1 ultrasonic sensor retainer on the other side.

  1. E154135
    Detach the 2 claws and remove the ultrasonic sensor retainer from the front bumper cover.


4. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)

  1. E155839
    Detach the 2 clamps.

  1. Remove the 3 bolts and fog light.


5. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedures described for the LH side.


6. REMOVE FRONT BUMPER HOLE COVER LH (w/o Fog Light)

B181003
  1. Remove the 3 screws and bumper hole cover.


7. REMOVE FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Use the same procedures described for the LH side.


8. REMOVE LOWER RADIATOR GRILLE LH

B181002
  1. w/ Headlight Cleaner System:
    Detach the 2 headlight cleaner hose clamps.

  1. Detach the 7 claws and remove the lower radiator grille.


9. REMOVE LOWER RADIATOR GRILLE RH

HINT:
Use the same procedures described for the LH side.


10. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

HINT:
Use the same procedures for the RH side and the LH side.

  1. E119628
    Extend the headlight washer nozzle.

  1. B182297
    Detach the 2 claws and remove the washer nozzle.


11. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedures described for the LH side.


12. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

HINT:
Use the same procedures for the RH side and the LH side.

  1. B182299E01
    Disconnect the headlight washer hose.

  1. B182298
    Remove the bolt.

  1. Disengage the 2 claws and remove the headlight washer actuator sub-assembly as shown in the illustration.


13. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedures described for the LH side.


14. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET

B185498
  1. for Type A:
    Remove the front bumper extension mounting bracket.

    1. Remove the 2 bolts and bracket.

  1. B185499
    for Type B:
    Remove the front bumper extension mounting bracket.

    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the bracket.


15. REMOVE FRONT BUMPER GUARD (w/ Garnish)

B185496
  1. Remove the 4 nuts.

  1. Detach the 6 clips and remove the bumper guard.


16. REMOVE FRONT BUMPER PROTECTOR

B181004
  1. Remove the 2 bumper protectors.


17. REMOVE FRONT NO. 2 BUMPER PROTECTOR

B181001
  1. Remove the 2 bumper protectors.

← REMOVAL (from Jan 2012)DISASSEMBLY (from Jan 2012) →