2011-2013 Land Cruiser · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

  1. Remove the 4 clamps and headlight cleaner hose.

    B302166

  1. B302165E01
    Disconnect the headlight cleaner hose.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side


2. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. B302163
    Extend the type 1 headlight washer nozzle sub-assembly LH.

  1. B302164
    Detach the 2 claws and remove the type 1 headlight washer nozzle sub-assembly LH.


3. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


4. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. B302167
    Remove the bolt.

  1. Detach the 2 claws and remove the headlight washer actuator sub-assembly LH.


5. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


6. REMOVE NO. 4 ENGINE ROOM WIRE

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Remove the No. 4 engine room wire.

    1. Disconnect the 2 connectors.

    2. Detach the 11 clamps and remove the No. 4 engine room wire.

      B302195

  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Remove the No. 4 engine room wire.

    1. Disconnect the 4 connectors.

    2. Detach the 12 clamps and remove the No. 4 engine room wire.

      B302156

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Remove the No. 4 engine room wire.

    1. Disconnect the 2 connectors.

    2. Detach the 12 clamps and remove the No. 4 engine room wire.

      B302210


7. REMOVE ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

  1. E244157
    Detach the 4 claws and remove the ultrasonic sensor clip.


8. REMOVE NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to remove the No. 1 ultrasonic sensor on the other side.

  1. E244158
    While pushing down on the lever with a finger to release the one claw, detach the claw on the other side to remove the No. 1 ultrasonic sensor.

    HINT:
    The type of claw on the top and bottom of the sensor are different. Observe the claws carefully before removing the No. 1 ultrasonic sensor.


9. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:
Use the same procedure to remove the No. 2 ultrasonic sensor retainer on the other side.

  1. E244159
    Detach the 2 claws and remove the No. 2 ultrasonic sensor retainer from the front bumper cover.


10. REMOVE FRONT BUMPER INNER BRACKET (w/ Fog Light)

  1. B302157
    Detach the 3 claws and remove the front bumper inner bracket.


11. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)

  1. E244776
    Remove the 2 screws.
    Text in Illustration 
    V100135
    Screw
    V100136
    Connector

  1. Detach the 2 guides and remove the fog light assembly LH.

  1. Disconnect the connector.


12. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.


13. REMOVE FRONT BUMPER HOLE COVER LH (w/ Fog Light)

  1. B302159
    Remove the 2 retainers and the 2 screws.

  1. B310833
    Detach the 5 claws and remove the front bumper hole cover LH.


14. REMOVE FRONT BUMPER HOLE COVER RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.


15. REMOVE FRONT BUMPER HOLE COVER LH (w/o Fog Light)

  1. B302160
    Remove the 2 retainers and the screw.

  1. B310834
    Detach the 5 claws and remove the front bumper hole cover LH.


16. REMOVE FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Use the same procedure described for the LH side.


17. REMOVE LOWER NO. 1 RADIATOR GRILLE
  1. Remove the 4 retainers.

  1. Detach the 16 claws and remove the lower No. 1 radiator grille.

    B302161E01

    Text in Illustration 
    *1
    Retainer
    -
    -


18. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket)

  1. B302211
    Remove the 2 bolts.

  1. Detach the 2 claws and remove the front bumper extension mounting bracket.


19. REMOVE FRONT BUMPER GUARD (w/ Garnish)

  1. B302212
    Remove the 4 nuts.

  1. Detach the 6 clips and remove the front bumper guard.


20. REMOVE FRONT NO. 2 BUMPER PROTECTOR

  1. B302162
    Remove the 2 front No. 2 bumper protectors.

← DISASSEMBLY (Sep 2011 – Dec 2011)REASSEMBLY (Sep 2011 – Dec 2011) →