2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
When installing the front bumper protector, heat the front bumper surface using a heat light.

Standard Heating Temperature:
Item
Temperature
Front Bumper
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the front bumper excessively.


1. INSTALL FRONT NO. 2 BUMPER PROTECTOR
  1. Clean the front bumper surface.

    1. Using a heat light, heat the front bumper surface.

    2. Remove the double-sided tape from the front bumper.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B181001
    Install a new bumper protector.

    1. Remove the peeling paper from the face of 2 new bumper protectors.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    2. Install the 2 bumper protectors as shown in the illustration.


2. INSTALL FRONT BUMPER PROTECTOR
  1. Clean the front bumper surface.

    1. Using a heat light, heat the front bumper surface.

    2. Remove the double-sided tape from the front bumper.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B181004
    Install a new bumper protector.

    1. Remove the peeling paper from the face of 2 new bumper protectors.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    2. Install the 2 bumper protectors as shown in the illustration.


3. INSTALL FRONT BUMPER GUARD (w/ Garnish)

B185496
  1. Attach the 6 clips to install the bumper guard.

  1. Install the 4 nuts.


4. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET

B185498
  1. for Type A:
    Install the front bumper extension mounting bracket.

    1. Install the bracket with the 2 bolts.

  1. B185499
    for Type B:
    Install the front bumper extension mounting bracket.

    1. Attach the 2 claws to install the bracket.

    2. Install the 2 bolts.


5. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

HINT:
Use the same procedures for the RH side and the LH side.

  1. Attach the 2 claws.

  1. B182298
    Install the headlight washer actuator sub-assembly with the bolt.

    Torque:
    1.1 N*m{ 11 kgf*cm , 10 in.*lbf }

  1. B182299E01
    Connect the headlight washer hose.


6. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedures described for the LH side.


7. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. B182297
    Attach the 2 claws to install the headlight washer nozzle.

  1. E119841
    Return the headlight washer nozzle to its original position.


8. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedures described for the LH side.


9. INSTALL LOWER RADIATOR GRILLE LH

B181002
  1. Attach the 7 claws to install the lower radiator grille.

  1. w/ Headlight Cleaner System:
    Attach the 2 headlight cleaner hose clamps.


10. INSTALL LOWER RADIATOR GRILLE RH

HINT:
Use the same procedures described for the LH side.


11. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)

B181003
  1. Install the bumper hole cover with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


12. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Use the same procedures described for the LH side.


13. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

  1. E155858
    Attach the claw.

  1. Connector the connectors.

  1. Install the fog light with the 2 nuts.


14. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedures described for the LH side.


15. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

E156306E01

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor retainer on the other side.

  1. Align the keyhole and protrusion as shown in the illustration.

  1. Install the ultrasonic sensor retainer to the front bumper cover.

    NOTICE:
    Do not damage the bumper with the protrusion when installing the retainer.


16. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

E146466

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor on the other side.

  1. Attach the 2 claws to install the ultrasonic sensor.

  1. Connect the connector.


17. INSTALL NO. 4 ENGINE ROOM WIRE

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 9 clamps to install the engine room wire.

    2. Connect the 2 connectors.

      B182885

  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 9 clamps to install the engine room wire.

    2. Connect the 4 connectors.

      B180531

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 9 clamps to install the engine room wire.

    2. Connect the 2 connectors.

      B185492

← DISASSEMBLY (from Jan 2012)REASSEMBLY (from Jan 2012) →