INSTALLATION
Removal / installation · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
Install the No. 2 luggage compartment side cover protector with 2 new grommets.
Install the 2 screws.
| 2. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
- HINT:
- Use the same procedure described for the LH side.
| 3. INSTALL REAR BUMPER ARM BRACKET LH |
Install the rear bumper arm bracket LH with the 2 bolts.
Connect the connector.
| 4. INSTALL REAR BUMPER ARM BRACKET |
Install the rear bumper arm bracket with the bolt.
- HINT:
- Use the same procedure to install the rear bumper arm bracket on the other side.
| 5. INSTALL REAR NO. 2 BUMPER REINFORCEMENT |
Install the rear No. 2 bumper reinforcement with the 2 bolts.
| 6. INSTALL REAR BUMPER SIDE SUPPORT LH |
Attach the 6 claws to install the rear bumper side support LH.
Install the 3 screws.
| 7. INSTALL REAR BUMPER SIDE SUPPORT RH |
- HINT:
- Use the same procedure described for the LH side.
| 8. INSTALL REAR UPPER BUMPER RETAINER LH |
Attach the 2 clips to install the rear upper bumper retainer LH.
| 9. INSTALL REAR UPPER BUMPER RETAINER RH |
- HINT:
- Use the same procedure described for the LH side.
| 10. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH |
Connect the connector.
Attach the 2 clips to install the rear combination light assembly LH.
Install the 2 bolts.
Attach the 6 claws and install the 2 covers.
| 11. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 12. INSTALL REAR BUMPER COVER |
- HINT:
- For the rear bumper cover with tire carrier, use the procedures described below.
w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:
Connect the No. 2 frame wire connector.
Attach the 14 claws to install the rear bumper cover.
Install the 7 bolts, 6 screws and 2 clips.
Open the tail gate and install the 4 clips.
Close the tail gate.
| 13. INSTALL REAR NO. 1 BUMPER PLATE |
Attach the 20 claws to install the rear No. 1 bumper plate.
| 14. INSTALL REAR QUARTER PANEL MUDGUARD LH |
![]() ![]() |
Install the mudguard with the clip.
Using a T30 "TORX" socket, install the 6 screws.
| 15. INSTALL REAR QUARTER PANEL MUDGUARD RH |
![]() ![]() |
Install the mudguard with the clip.
Using a T30 "TORX" socket, install the 7 screws.
| 16. INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier) |
Clean the threaded surfaces on the vehicle body with a non-residue solvent.
Apply adhesive to the threads of the 6 bolts.
- Adhesive:
- Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the spare wheel carrier with the 6 bolts.
- Torque:
- 28.4 N*m{ 290 kgf*cm , 21 ft.*lbf }


Install the spare tire.
- Torque:
- 90 N*m{ 918 kgf*cm , 66 ft.*lbf }
| 17. INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier) |
![]() ![]() |
Attach the clip to install the cover.
Install the 2 nuts.
| 18. INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier) |
![]() ![]() |
Attach the 2 claws to install the bracket.
| 19. INSTALL PINTLE HOOK ASSEMBLY |
Install the pintle hook assembly and pintle hook bracket with the 2 bolts, 2 eyelet pintle hooks and 4 nuts.
- Torque:
- for nut:
- 65 N*m{ 663 kgf*cm , 48 ft.*lbf }
For vehicles with a spare installed to the underbody, install the spare tire.




