2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

B190217
  1. Install the protector with 2 new grommets.

  1. Install the 2 screws.


2. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

HINT:
Use the same procedures described for the LH side.


3. INSTALL REAR BUMPER ARM BRACKET LH

  1. B181013
    Install the bumper arm bracket with the 2 bolts.

  1. Connect the connector.


4. INSTALL REAR BUMPER ARM BRACKET

B181012

HINT:
Use the same procedure to install the bumper arm bracket on the other side.

  1. Install the bumper arm bracket with the bolt.


5. INSTALL REAR NO. 2 BUMPER REINFORCEMENT

B185555
  1. Install the bumper reinforcement with the 2 bolts.


6. INSTALL REAR BUMPER SIDE SUPPORT LH

B181014
  1. Attach the 6 claws to install the bumper side support.

  1. Install the 3 screws.


7. INSTALL REAR BUMPER SIDE SUPPORT RH

HINT:
Use the same procedures described for the LH side.


8. INSTALL UPPER REAR BUMPER RETAINER LH

B181015
  1. Attach the 2 clips to install the bumper retainer.


9. INSTALL UPPER REAR BUMPER RETAINER RH

HINT:
Use the same procedures described for the LH side.


10. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

  1. E155847
    Connect the connector.

  1. Attach the 2 clips to install the rear combination light.

  1. Install the 2 bolts.


11. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


12. INSTALL REAR BUMPER COVER

HINT:
For the rear bumper cover with tire carrier, use the procedures described below.

  1. w/o TOYOTA Parking Assist-sensor System, w/o Rear Fog Light:
    Attach the 14 claws to install the bumper cover.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:
    Connect the No. 2 frame wire connector and attach the 14 claws to install the bumper cover.

  1. Install the 7 bolts, 6 screws and 2 clips.

    B184216

  1. Open the tail gate and install the 4 clips.

    B184215

  1. Close the tail gate.


13. INSTALL REAR NO. 1 BUMPER PLATE

  1. Attach the 20 claws to install the bumper plate.

    B184213


14. INSTALL REAR QUARTER PANEL MUDGUARD LH

B180882
  1. Install the mudguard with the clip.

  1. Using a T30 "TORX" socket, install the 6 screws.


15. INSTALL REAR QUARTER PANEL MUDGUARD RH

B180883
  1. Install the mudguard with the clip.

  1. Using a T30 "TORX" socket, install the 7 screws.


16. INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)
  1. Clean the threaded surfaces on the vehicle body with a non-residue solvent.

  1. Apply adhesive to the threads of the 6 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the spare wheel carrier with the 6 bolts.

    Torque:
    28.4 N*m{ 290 kgf*cm , 21 ft.*lbf }


    B186196

  1. Install the spare tire.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }


17. INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

B186195
  1. Attach the clip to install the cover.

  1. Install the 2 nuts.


18. INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

B186194
  1. Attach the 2 claws to install the bracket.


19. INSTALL PINTLE HOOK ASSEMBLY

B185550E01
  1. Install the pintle hook assembly and pintle hook bracket with the 2 bolts, 2 eyelet pintle hooks and 4 nuts.

    Torque:
    for nut:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. For vehicles with a spare installed to the underbody, install the spare tire.

← REASSEMBLY (from Jan 2012)INSTALLATION (from Jan 2012) →