REMOVAL
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1. REMOVE SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier) |
![]() ![]() |
Detach the 2 claws and remove the bracket.
| 2. REMOVE SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier) |
![]() ![]() |
Remove the 2 nuts.
Detach the clip and remove the cover.
| 3. REMOVE SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier) |
Remove the spare tire.
Remove the 6 bolts and spare wheel carrier.


| 4. REMOVE REAR QUARTER PANEL MUDGUARD LH |
![]() ![]() |
Remove the clip.
Using a T30 "TORX" socket, remove the 6 screws and mudguard.
| 5. REMOVE REAR QUARTER PANEL MUDGUARD RH |
![]() ![]() |
Remove the clip.
Using a T30 "TORX" socket, remove the 7 screws and mudguard.
| 6. REMOVE REAR NO. 1 BUMPER PLATE |
Put protective tape around the bumper plate.
Detach the 20 claws and remove the bumper plate.


| 7. REMOVE REAR BUMPER COVER |
- HINT:
- For the rear bumper cover with tire carrier, use the procedures described below.
Put protective tape around the bumper cover.


Open the tail gate and remove the 4 clips.


Close the tail gate.
Remove the 7 bolts, 6 screws and 2 clips.
w/o TOYOTA Parking Assist-sensor System, w/o Rear Fog Light:
Detach the 14 claws and remove the bumper cover.
w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:
Detach the 14 claws, disconnect the No. 2 frame wire connector and remove the bumper cover.

| 8. REMOVE REAR COMBINATION LIGHT ASSEMBLY LH |
Remove the 2 bolts.

Detach the 2 clips and remove the rear combination light.
Disconnect the connector.
| 9. REMOVE REAR COMBINATION LIGHT ASSEMBLY RH |
- HINT:
- Use the same procedures described for the LH side.
| 10. REMOVE REAR UPPER BUMPER RETAINER LH |
![]() ![]() |
Detach the 2 clips and remove the bumper retainer.
| 11. REMOVE REAR UPPER BUMPER RETAINER RH |
- HINT:
- Use the same procedures described for the LH side.
| 12. REMOVE REAR BUMPER SIDE SUPPORT LH |
![]() ![]() |
Remove the 3 screws.
Detach the 6 claws and remove the bumper side support.
| 13. REMOVE REAR BUMPER SIDE SUPPORT RH |
- HINT:
- Use the same procedures described for the LH side.
| 14. REMOVE REAR NO. 2 BUMPER REINFORCEMENT |
![]() ![]() |
Remove the 2 bolts and bumper reinforcement.
| 15. REMOVE REAR BUMPER ARM BRACKET |
![]() ![]() |
- HINT:
- Use the same procedure to remove the bumper arm bracket on the other side.
Remove the bolt and bumper arm bracket.
| 16. REMOVE REAR BUMPER ARM BRACKET LH |
![]() ![]() |
Disconnect the connector.
Remove the 2 bolts and bumper arm bracket.
| 17. REMOVE NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
![]() ![]() |
Remove the 2 screws, 2 grommets and protector.
| 18. REMOVE NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
- HINT:
- Use the same procedures described for the LH side.










