REMOVAL
Removal / installation · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1.
REMOVE SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)
|
 |
Detach the 2 claws and remove the bracket.
| 2.
REMOVE SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)
|
 |
Remove the 2 nuts.
Detach the clip and remove the cover.
| 3.
REMOVE SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)
|
 |
Remove the spare tire.
Remove the 6 bolts and spare wheel carrier.


| 4.
REMOVE REAR QUARTER PANEL MUDGUARD LH
|
 |
Remove the clip.
Using a T30 "TORX" socket, remove the 6 screws and mudguard.
| 5.
REMOVE REAR QUARTER PANEL MUDGUARD RH
|
 |
Remove the clip.
Using a T30 "TORX" socket, remove the 7 screws and mudguard.
| 6.
REMOVE REAR NO. 1 BUMPER PLATE |
 |
Put protective tape around the rear No. 1 bumper plate.
Detach the 20 claws and remove the rear No. 1 bumper plate.


Text in Illustration
*1
|
Protective Tape
|
-
|
-
|
| 7.
REMOVE REAR BUMPER COVER |
 |
- HINT:
- For the rear bumper cover with tire carrier, use the procedures described below.
Put protective tape around the rear bumper cover.


Text in Illustration
*1
|
Protective Tape
|
-
|
-
|
Open the tail gate and remove the 4 clips.


Close the tail gate.
Remove the 7 bolts, 6 screws and 2 clips.
Detach the 14 claws and remove the rear bumper cover.


w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:
Disconnect the No. 2 frame wire connector.
| 8.
REMOVE REAR COMBINATION LIGHT ASSEMBLY LH
|
 |
- Using a screwdriver wrapped with protective tape, detach the 6 claws and remove the 2 cover.
Text in Illustration
*1
|
Protective Tape
|
- Put protective tape around the rear combination light assembly LH.
Text in Illustration
*1
|
Protective Tape
|
Remove the 2 bolts.
Detach the 2 clips and remove the rear combination light assembly LH.
Disconnect the connector.
| 9.
REMOVE REAR COMBINATION LIGHT ASSEMBLY RH |
 |
- HINT:
- Use the same procedure described for the LH side.
| 10.
REMOVE REAR UPPER BUMPER RETAINER LH |
 |
- Detach the 2 clips and remove the rear upper bumper retainer LH.
| 11.
REMOVE REAR UPPER BUMPER RETAINER RH |
 |
- HINT:
- Use the same procedure described for the LH side.
| 12.
REMOVE REAR BUMPER SIDE SUPPORT LH |
 |
- Remove the 3 screws.
Detach the 6 claws and remove the rear bumper side support LH.
| 13.
REMOVE REAR BUMPER SIDE SUPPORT RH |
 |
- HINT:
- Use the same procedure described for the LH side.
| 14.
REMOVE REAR NO. 2 BUMPER REINFORCEMENT |
 |
- Remove the 2 bolts and rear No. 2 bumper reinforcement.
| 15.
REMOVE REAR BUMPER ARM BRACKET |
 |
- Remove the bolt and rear bumper arm bracket.
- HINT:
- Use the same procedure to remove the rear bumper arm bracket on the other side.
| 16.
REMOVE REAR BUMPER ARM BRACKET LH |
 |
- Disconnect the connector.
Remove the 2 bolts and rear bumper arm bracket LH.
| 17.
REMOVE NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
 |
Remove the 2 screws, 2 grommets and No. 2 luggage compartment side cover protector.
| 18.
REMOVE NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
 |
- HINT:
- Use the same procedure described for the LH side.