2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE REAR QUARTER PANEL MUDGUARD LH

B180882
  1. Remove the clip.

  1. Using a T30 "TORX" socket, remove the 6 screws and mudguard.


2. REMOVE REAR QUARTER PANEL MUDGUARD RH

B180883
  1. Remove the clip.

  1. Using a T30 "TORX" socket, remove the 7 screws and mudguard.


3. REMOVE REAR NO. 1 BUMPER PLATE
  1. Put protective tape around the rear No. 1 bumper plate.

  1. Detach the 20 claws and remove the rear No. 1 bumper plate.

    B181008E02

    Text in Illustration 
    *1
    Protective Tape
    -
    -


4. REMOVE REAR BUMPER COVER

  1. Put protective tape around the bumper cover.

    B302233E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Open the tail gate and remove the 4 clips.

    B302234

  1. Close the tail gate.

  1. Remove the 7 bolts, 6 screws and 2 clips.

  1. Detach the 14 claws and remove the rear bumper cover.

    B302235

  1. w/ TOYOTA Parking Assist-sensor System:
    Disconnect the No. 2 frame wire connector.


5. REMOVE REAR COMBINATION LIGHT ASSEMBLY LH

  1. E244781E01
    Using a screwdriver wrapped with protective tape, detach the 6 claws and remove the 2 cover.
    Text in Illustration 
    *1
    Protective Tape

  1. E244782E01
    Put protective tape around the rear combination light assembly LH.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 2 bolts.

  1. Detach the 2 clips and remove the rear combination light assembly LH.

  1. Disconnect the connector.


6. REMOVE REAR COMBINATION LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


7. REMOVE REAR UPPER BUMPER RETAINER LH

  1. B181015
    Detach the 2 clips and remove the rear upper bumper retainer LH.


8. REMOVE REAR UPPER BUMPER RETAINER RH

HINT:
Use the same procedure described for the LH side.


9. REMOVE REAR BUMPER SIDE SUPPORT LH

  1. B181014
    Remove the 3 screws.

  1. Detach the 6 claws and remove the rear bumper side support LH.


10. REMOVE REAR BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure described for the LH side.


11. REMOVE REAR NO. 2 BUMPER REINFORCEMENT

  1. B181019
    Remove the 2 bolts and rear No. 2 bumper reinforcement.


12. REMOVE REAR BUMPER ARM BRACKET

  1. B181012
    Remove the bolt and rear bumper arm bracket.

    HINT:
    Use the same procedure to remove the bumper arm bracket on the other side.


13. REMOVE REAR BUMPER ARM BRACKET LH

  1. B181013
    Disconnect the connector.

  1. Remove the 2 bolts and rear bumper arm bracket LH.


14. REMOVE NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

  1. B190217
    Remove the 2 screws, 2 grommets and No. 2 luggage compartment side cover protector.


15. REMOVE NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

HINT:
Use the same procedure described for the LH side.

← REMOVAL (Sep 2011 – Dec 2011)DISASSEMBLY (Sep 2011 – Dec 2011) →