2011-2013 Land Cruiser · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL REAR SEAT LOCK CONTROL LEVER LH

B181797
  1. Install the lock control lever with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

B181798
  1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

  1. Tighten the 5 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Using a T40 "TORX" socket, tighten the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


3. INSTALL NO. 1 SEAT LEG ASSEMBLY LH

B181799
  1. Using a T40 "TORX" socket, install the seat leg assembly with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


4. INSTALL REAR SEAT INNER BELT ASSEMBLY

B185853E01
  1. Install the seat belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    The anchor part of the seat belt must not overlap the protruding part.


5. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

B182640
  1. Attach the 2 claws to install the seat heater control.


6. INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)

B182639
  1. Install the holder bracket with the 2 screws.

  1. Connect the seat wire connector.


7. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

  1. B181796E01
    Attach the clamp to install the seat lock cable.

  1. Attach the 3 cable clamps to connect the 3 cables.

  1. Connect the cable and install a new cable tie.

  1. B181203
    Install the lower seat track bracket with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


8. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

B181795
  1. Install the 2 fold seat lock control cables.

  1. Attach the 2 cable clamps to connect the 2 cables.


9. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH

  1. B184962
    Install the lower seatback cover.

  1. B181793
    Temporarily install the seatback frame with the 4 bolts.

  1. LH Side:
    Using a T40 "TORX" socket, tighten the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. RH Side:
    Using a T55 "TORX" socket, tighten the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


10. INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

B184052
  1. Attach the clamp to install the lock control cable.

  1. Attach the 2 cable clamps to connect the cable.


11. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH

B181792
  1. Attach the clamp to install the adjusting cable.

  1. Attach the 2 cable clamps to connect the cable.


12. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B185876E01
  1. Install the belt with the nut labeled A.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the belt sensor with the 3 nuts labeled B.


13. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

B188669
  1. Install the seat belt as shown in the illustration.

  1. B185854
    Attach the 3 claws to install the shoulder belt hole cover.


14. INSTALL REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH

B184963
  1. Attach the 4 claws to install the cover.

  1. Install the 4 screws.


15. INSTALL REAR SEATBACK HINGE COVER LH

B181237
  1. Attach the claw to install the cover.

  1. Install the screw.


16. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B181790
  1. Attach the claw to install the cover.

  1. Install the screw.


17. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

B181197
  1. Attach the clamp to install the cover.

  1. Install the screw.


18. INSTALL REAR SEAT RECLINING COVER LH

B181196
  1. Attach the claw to install the cover.

  1. Install the screw.


19. INSTALL CUP HOLDER ASSEMBLY (w/ Center Armrest)

  1. B184039
    Attach the 2 clips to install the cup holder.

  1. B190297
    Install the 2 screws.


20. INSTALL NO. 1 SEAT ARMREST PLATE (w/ Center Armrest)

B184038
  1. Attach the 2 claws and 4 clips to install the 2 armrest plates.


21. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

22. INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)

B181252
  1. Using a T40 "TORX" socket, install the center seat armrest with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


23. INSTALL SEATBACK STOPPER PLATE

  1. w/ Center Armrest:

    1. Install the bush to the stopper plate.

    2. B181250
      Temporarily install the stopper plate with the 3 bolts.

    3. Using a T40 "TORX" socket, tighten the 2 bolts.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    4. Tighten the bolt.

      Torque:
      15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. w/o Center Armrest:

    1. Install the bush to the stopper plate.

    2. B181251
      Temporarily install the stopper plate with the 3 bolts.

    3. Using a T40 "TORX" socket, tighten the 2 bolts.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    4. Tighten the bolt.

      Torque:
      15 N*m{ 153 kgf*cm , 11 ft.*lbf }


24. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with new tack pins.

    B181208E01


25. INSTALL REAR SEPARATE TYPE SEATBACK COVER

  1. B184037E01
    w/ Center Armrest:
    Using hog ring pliers, install the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B189167E01
    w/o Center Armrest:
    Using hog ring pliers, install the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B184024
    w/ Rear Seat Side Airbag:
    Connect the seatback cover bracket to the seatback pad.


26. INSTALL SEATBACK COVER WITH PAD
  1. Install the seatback cover with pad.

  1. B184030
    w/ Center Armrest:
    Pull out the seat belt.

  1. B189169
    w/o Center Armrest:
    Pull out the seat belt.

  1. w/ Rear Seat Side Airbag:
    Pass the side airbag wire harness through the hole in the seatback.

  1. w/ Seat Heater System:
    Pass the seatback heater wire harness through the hole in the seatback.

    1. B184057

    2. B182598E01
      Connect the seatback heater wire harness and install a new cable tie.

  1. B184020
    w/ Rear Seat Side Airbag:
    Install the seatback cover bracket to the seat frame with the cap nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

  1. B262669E01
    w/ Center Armrest:
    Using hog ring pliers, install new hog rings to the seatback frame.

  1. B262670E01
    w/o Center Armrest:
    Using hog ring pliers, install new hog rings to the seatback frame.


27. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

B181239
  1. Attach the 4 claws to install the cover.

  1. Install the screw.


28. INSTALL SHOULDER BELT ANCHOR COVER

B184040
  1. Attach the 2 claws to install the cover.


29. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

  1. B181190
    w/ Center Armrest:
    Attach the 4 claws to install the 2 supports.

  1. B181243
    w/o Center Armrest:
    Attach the 8 claws to install the 4 supports.


30. INSTALL REAR SEAT HEADREST ASSEMBLY

31. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

  1. B184026
    w/ Center Armrest:

    1. Push the board down to attach the 2 claws on the bottom.

    2. Attach the 2 claws on the top of the board to install it.

  1. B189166
    w/o Center Armrest:

    1. Push the board down to attach the 3 claws on the bottom.

    2. Attach the 3 claws on the top of the board to install it.


32. INSTALL REAR SEATBACK COVER

B182667
  1. Attach the 4 claws to install the cover.


33. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with new tack pins.

    B181209E01


34. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

B184036E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B181234E01
    Attach the 3 pieces of fastening tape.


35. INSTALL SEAT CUSHION COVER WITH PAD
  1. Install the seat cushion cover with pad.

  1. w/ Rear Seat Side Airbag:
    Pass the side airbag wire harness through the hole in the seat cushion.

  1. w/ Seat Heater System:

    1. B184056
      Pass the seatback heater wire harness through the hole in the seat cushion.

    2. B182596
      Connect the 2 seat heater connectors.

  1. w/ Rear Seat Side Airbag:
    Attach the side airbag wire harness clamps.


36. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B184533E01
  1. Connect the belt anchor.

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.


37. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B184532E01
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    HINT:
    The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.


38. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

39. INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY

  1. B181183
    Attach the cable clamp to connect the cable.

  1. B181182
    Attach the 2 cable clamps to connect the 2 cables.

  1. B182656
    Install the seat track handle with the 2 screws.


40. INSTALL REAR SEAT UNDER TRAY COVER LH

B181181
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


41. INSTALL REAR SEAT CUSHION COVER RH

B181231
  1. Attach the 2 claws to install the cover.

  1. Install the 4 screws.


42. INSTALL NO. 1 SEAT CUSHION PLATE

B181180
  1. Attach the 3 claws to install the seat cushion plate.


43. INSTALL REAR UNDER SIDE COVER LH

B181230
  1. Attach the 2 claws and 2 clips to install the cover.

  1. Install the 5 screws.

  1. B181229
    Attach the 10 claws.


44. INSTALL REAR SEATBACK STAY COVER LH

B181226
  1. Attach the 2 claws to install the cover.

  1. Install the screw.


45. INSTALL SEAT BELT ANCHOR COVER CAP

  1. B181228
    Install the anchor cover cap with the screw.

  1. B184029
    Attach the claw to close the cap.


46. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B184017
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


47. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

  1. B181176
    Attach the cable clamp to connect the cable.

  1. B184045
    Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear Seat Side Airbag:
    Attach the wire harness clamp.

  1. w/ Seat Heater System:
    Attach the wire harness clamp.


48. INSTALL REAR NO. 2 SEAT PROTECTOR
  1. Install the wire harness, and attach 2 claws to close the protector.

  1. B182595
    Attach the claw to install the protector to the seat hinge.

  1. Install the clip.

  1. B184016
    w/ Rear Seat Side Airbag:
    Attach the claw to install the wire harness connector.

  1. w/ Seat Heater System:
    Attach the claw to install the wire harness connector.


49. INSTALL REAR SEAT SIDE HINGE MALE COVER RH

  1. B181173
    Attach the clip to install the cover.


50. INSTALL REAR SEAT SIDE HINGE MALE COVER LH
  1. Attach the clip to install the cover.


51. INSTALL REAR SEAT SIDE HINGE FEMALE COVER

  1. B181172
    Attach the 6 claws to install the 2 covers.


52. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY
  1. Install the fold seat stopper band to the seat leg side cover.


53. INSTALL REAR NO. 2 SEAT LEG SIDE COVER

  1. B184044
    Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

  1. B181224
    Attach the 4 claws to install the seat leg side cover.

  1. Install the 4 screws.


54. INSTALL NO. 1 SEAT CUSHION COVER

B181223
  1. Attach the 4 claws to install the 2 covers.


55. INSTALL UPPER SEAT TRACK RAIL COVER RH

B184041
  1. Attach the 2 claws to install the cover.


56. INSTALL UPPER SEAT TRACK RAIL COVER LH

B184028
  1. Attach the 2 claws to install the cover.


57. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B184015
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


58. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

B184027E01
  1. Attach the 3 claws in the order shown in the illustration to install the cover.

  1. Install the 2 screws.


59. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B184013
  1. Install the release handle with the screw.


60. INSTALL SEAT ADJUSTER BOLT COVER

B184012
  1. Attach the 2 claws to install the cover.

← DISASSEMBLY (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →