2011-2013 Land Cruiser · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE SEAT ADJUSTER BOLT COVER

B184012
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B184013
  1. Remove the screw and release handle.


3. REMOVE REAR NO. 1 SEAT RECLINING COVER LH

B184014E01
  1. Remove the 2 screws.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cover.


4. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

B184015
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


5. REMOVE UPPER SEAT TRACK RAIL COVER LH

B181222
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


6. REMOVE UPPER SEAT TRACK RAIL COVER RH

B184035
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


7. REMOVE NO. 1 SEAT CUSHION COVER

B181223
  1. Detach the 4 claws and remove the 2 covers.


8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER

  1. B181224
    Remove the 4 screws and detach the 4 claws.

  1. B184044
    Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.


9. REMOVE FOLD SEAT STOPPER BAND ASSEMBLY
  1. Remove the fold seat stopper band from the seat leg side cover.


10. REMOVE REAR SEAT SIDE HINGE FEMALE COVER

B181172
  1. Using a screwdriver, detach the 6 claws and remove the 2 covers.

    HINT:
    Tape the screwdriver tip before use.


11. REMOVE REAR SEAT SIDE HINGE MALE COVER LH

B181173
  1. Detach the clip and remove the cover.


12. REMOVE REAR SEAT SIDE HINGE MALE COVER RH
  1. Detach the clip and remove the cover.


13. REMOVE REAR NO. 2 SEAT PROTECTOR

  1. B184016
    w/ Rear Seat Side Airbag:
    Detach the claw and remove the wire harness connector.

  1. w/ Seat Heater System:
    Detach the claw and remove the wire harness connector.

  1. B182595
    Using a clip remover, remove the clip.

  1. Detach the claw and remove the seat protector from the seat hinge.

  1. Detach the 2 claws, open the protector and remove wire harness.


14. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

  1. B184045
    w/ Rear Seat Side Airbag:
    Detach the wire harness clamp.

  1. w/ Seat Heater System:
    Detach the wire harness clamp.

  1. Remove the 2 nuts and hinge.

  1. B181176
    Detach the cable clamp and disconnect the cable.


15. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B184017
  1. Remove the 2 nuts and hinge.


16. REMOVE SEAT BELT ANCHOR COVER CAP

  1. B181227
    Detach the claw and open the cap.

  1. B181228
    Remove the screw and anchor cover cap.


17. REMOVE REAR SEATBACK STAY COVER LH

B181226
  1. Remove the screw.

  1. Detach the 2 claws and remove the cover.


18. REMOVE REAR UNDER SIDE COVER LH

  1. B181229
    Detach the 10 claws.

  1. B181230
    Remove the 5 screws.

  1. Detach the 2 clips and 2 claws, and remove the cover.


19. REMOVE NO. 1 SEAT CUSHION PLATE

  1. B181180
    Detach the 3 claws and remove the seat cushion plate.


20. REMOVE REAR SEAT CUSHION COVER RH

B181231
  1. Remove the 4 screws.

  1. Detach the 2 claws and remove the cover.


21. REMOVE REAR SEAT UNDER TRAY COVER LH

B181181
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


22. REMOVE REAR SEAT TRACK HANDLE SUB-ASSEMBLY

  1. B182656
    Remove the 2 screws and seat track handle.

  1. B181182
    Detach the 2 cable clamps and disconnect the 2 cables.

  1. B181183
    Detach the cable clamp and disconnect the cable.


23. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

24. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B184531E01
  1. Remove the bolt and belt.

    HINT:
    The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.


25. DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B184533E02
  1. Disconnect the belt anchor.


26. REMOVE SEAT CUSHION COVER WITH PAD
  1. w/ Rear Seat Side Airbag:

    1. Detach the side airbag wire harness clamps.

    2. Remove the side airbag wire harness through the hole in the seat cushion.

  1. w/ Seat Heater System:

    1. B182596
      Disconnect the 2 seat heater connectors.

    2. B182597
      Remove the seatback heater wire harness through the hole in the seat cushion.

  1. Remove the seat cushion cover with pad.


27. REMOVE REAR SEPARATE TYPE SEAT CUSHION COVER

  1. B181234E01
    Detach the 3 pieces of fastening tape.

  1. B181236
    Remove the hog rings and cover.


28. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

B181187
  1. Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.


29. REMOVE REAR SEATBACK COVER

B181188E01
  1. Using a screwdriver, detach the 4 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


30. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH

B181241
  1. w/ Center Armrest:

    1. Detach the 2 claws on the top of the board.

    2. Pull up the board to detach the 2 claws on the bottom of the board and remove it.

  1. B181240
    w/o Center Armrest:

    1. Detach the 3 claws on the top of the board.

    2. Pull up the board to detach the 3 claws on the bottom of the board and remove it.


31. REMOVE REAR SEAT HEADREST ASSEMBLY

32. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B181190
  1. w/ Center Armrest:
    Detach the 4 claws and remove the 2 supports.

  1. B181243
    w/o Center Armrest:
    Detach the 8 claws and remove the 4 supports.


33. REMOVE SHOULDER BELT ANCHOR COVER

B181238E01
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


34. REMOVE REAR SEAT BELT HOLE COVER LH

B181239
  1. Remove the screw.

  1. Detach the 4 claws and remove the cover.


35. REMOVE SEATBACK COVER WITH PAD

  1. B262667
    w/ Center Armrest:
    Remove the hog rings.

  1. B262668
    w/o Center Armrest:
    Remove the hog rings.

  1. w/ Rear Seat Side Airbag:

    1. B184020
      Remove the cap nut and seatback cover bracket from the seat frame.

    2. Remove the side airbag wire harness through the hole in the seatback.

  1. w/ Seat Heater System:

    1. B182598E01
      Cut the cable tie and disconnect the seatback heater wire harness.

    2. B182638
      Remove the seatback heater wire harness through the hole in the seatback.

  1. B181245
    w/ Center Armrest:
    Pull the seat belt into the inside of the seat.

  1. B181248
    w/o Center Armrest:
    Pull the seat belt into the inside of the seat.

  1. Remove the seatback cover with pad.


36. REMOVE REAR SEPARATE TYPE SEATBACK COVER

  1. B184021
    w/ Rear Seat Side Airbag:
    Disconnect the seatback cover bracket from the seatback pad.

  1. B181246
    w/ Center Armrest:
    Remove the hog rings and rear seatback cover.

  1. B181249
    w/o Center Armrest:
    Remove the hog rings and rear seatback cover.


37. REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

B181195
  1. Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.


38. REMOVE SEATBACK STOPPER PLATE

  1. B181250
    w/ Center Armrest:

    1. Using a T40 "TORX" socket, remove the 2 bolts.

    2. Remove the bolt and stopper plate.

    3. Remove the bush from the stopper plate.

  1. B181251
    w/o Center Armrest:

    1. Using a T40 "TORX" socket, remove the 2 bolts.

    2. Remove the bolt and stopper plate.

    3. Remove the bush from the stopper plate.


39. REMOVE REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)

B181252
  1. Using a T40 "TORX" socket, remove the 2 bolts and center seat armrest.


40. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

41. REMOVE NO. 1 SEAT ARMREST PLATE (w/ Center Armrest)

B181253
  1. Using a moulding remover, detach the 4 clips and 2 claws, and then remove the 2 armrest plates.


42. REMOVE CUP HOLDER ASSEMBLY (w/ Center Armrest)

  1. B190297
    Remove the 2 screws.

  1. B181789
    Using a moulding remover, detach the 2 clips and remove the cup holder.


43. REMOVE REAR SEAT RECLINING COVER LH

B181196
  1. Remove the screw.

  1. Detach the claw and remove the cover.


44. REMOVE REAR NO. 2 SEAT RECLINING COVER LH

B181197
  1. Remove the screw.

  1. Detach the clamp and remove the cover.


45. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

B181790
  1. Remove the screw.

  1. Detach the claw and remove the cover.


46. REMOVE REAR SEATBACK HINGE COVER LH

B181237
  1. Remove the screw.

  1. Detach the claw and remove the cover.


47. REMOVE REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH

B181791
  1. Remove the 4 screws.

  1. Detach the 4 claws and remove the cover.


48. REMOVE REAR SEAT SHOULDER BELT HOLE COVER LH

B185854
  1. Using a screwdriver, detach the 3 claws and remove the shoulder belt hole cover.


49. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B185876
  1. Remove the 3 nuts and belt sensor.

  1. Remove the nut and then remove the outer belt.


50. REMOVE RECLINING ADJUSTING CABLE ASSEMBLY LH

B181792
  1. Detach the 2 cable clamps and disconnect the cable.

  1. Detach the clamp and remove the adjusting cable.


51. REMOVE NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

B184052
  1. Detach the 2 cable clamps and disconnect the cable.

  1. Detach the clamp and remove the lock control cable.


52. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH

B181793
  1. LH Side:
    Using a T40 "TORX" socket, remove the 2 bolts.

  1. RH Side:
    Using a T55 "TORX" socket, remove the 2 bolts.

  1. Remove the seatback frame sub-assembly.

  1. B181794
    Remove the lower seatback cover.


53. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

B181795
  1. Detach the 2 cable clamps and disconnect the 2 cables.

  1. Remove the 2 fold seat lock cables.


54. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

  1. B181203
    Remove the 2 nuts and lower seat track bracket.

  1. B181796E01
    Cut the cable tie and disconnect the cable.

  1. Detach the 3 cable clamps and disconnect the 3 cables.

  1. Detach the clamp and remove the seat lock cable.


55. REMOVE REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)

B182639
  1. Disconnect the seat wire connector.

  1. Remove the 2 screws and holder bracket.


56. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

B182640
  1. Detach the 2 claws and remove the seat heater control.


57. REMOVE REAR SEAT INNER BELT ASSEMBLY

B185852E01
  1. Remove the bolt and belt.


58. REMOVE NO. 1 SEAT LEG ASSEMBLY LH

B181799
  1. Using a T40 "TORX" socket, remove the 2 bolts and seat leg assembly.


59. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

B181798
  1. Using a T40 "TORX" socket, remove the bolt.

  1. Remove the 5 nuts and seat cushion frame.


60. REMOVE REAR SEAT LOCK CONTROL LEVER LH

B181797
  1. Remove the bolt and lock control lever.

← REMOVAL (from Jan 2012)REASSEMBLY (from Sep 2011) →