DISASSEMBLY
Removal / installation · Vehicles built from Sep 2011
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for RHD and LHD vehicles.
| 1. REMOVE SEAT ADJUSTER BOLT COVER |
![]() ![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH |
![]() ![]() |
Remove the screw and release handle.
| 3. REMOVE REAR NO. 1 SEAT RECLINING COVER RH |
![]() ![]() |
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the cover.
| 4. REMOVE REAR NO. 1 SEAT RECLINING COVER LH |
![]() ![]() |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 5. REMOVE UPPER SEAT TRACK RAIL COVER LH |
![]() ![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 6. REMOVE UPPER SEAT TRACK RAIL COVER RH |
![]() ![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 7. REMOVE NO. 1 SEAT CUSHION COVER |
![]() ![]() |
Detach the 4 claws and remove the 2 covers.
| 8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER |
Remove the 4 screws and detach the 3 claws.

Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.

| 9. REMOVE FOLD SEAT STOPPER BAND ASSEMBLY |
Remove the fold seat stopper band from the seat leg side cover.
| 10. REMOVE REAR SEAT SIDE HINGE FEMALE COVER |
![]() ![]() |
Using a screwdriver, detach the 6 claws and remove the 2 covers.
- HINT:
- Tape the screwdriver tip before use.
| 11. REMOVE REAR SEAT SIDE HINGE MALE COVER LH |
![]() ![]() |
Detach the clip and remove the cover.
| 12. REMOVE REAR SEAT SIDE HINGE MALE COVER RH |
Detach the clip and remove the cover.
| 13. REMOVE REAR NO. 2 SEAT PROTECTOR |
w/ Rear Seat Side Airbag:

Detach the claw and remove the wire harness connector.
w/ Seat Heater System:
Detach the claw and remove the wire harness connector.
Using a clip remover, remove the clip.

Detach the claw and remove the seat protector from the seat hinge.
Detach the 2 claws, open the protector and remove the wire harness.
| 14. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH |
![]() ![]() |
Remove the 2 nuts and hinge.
| 15. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH |
![]() ![]() |
w/ Rear Seat Side Airbag:
Detach the wire harness clamp.
w/ Seat Heater System:
Detach the wire harness clamp.
Remove the 2 nuts and hinge.
Detach the cable clamp and disconnect the cable.

| 16. REMOVE REAR SEAT COVER |
Detach the 12 claws.

Remove the 3 screws.

Detach the 2 claws and remove the cover.
| 17. REMOVE REAR UNDER SIDE COVER LH |
![]() ![]() |
Remove the 5 screws.
Detach the clip and 2 claws, and remove the cover.
| 18. REMOVE NO. 1 SEAT CUSHION PLATE |
![]() ![]() |
Detach the 3 claws and remove the seat cushion plate.
| 19. REMOVE REAR SEAT UNDER TRAY COVER RH |
![]() ![]() |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 20. REMOVE REAR SEAT TRACK HANDLE SUB-ASSEMBLY |
Remove the 2 screws and seat track handle.

Detach the 2 cable clamps and disconnect the 2 cables.

Detach the cable clamp and disconnect the cable.

| 21. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY |
| 22. REMOVE SEAT CUSHION COVER WITH PAD |
w/ Rear Seat Side Airbag:
Detach the side airbag wire harness clamps.
Remove the side airbag wire harness through the hole in the seat cushion.
w/ Seat Heater System:
Disconnect the 2 seat heater connectors.

Remove the seatback heater wire harness through the hole in the seat cushion.

Remove the seat cushion cover with pad.
| 23. REMOVE REAR SEPARATE TYPE SEAT CUSHION COVER |
Detach the 3 pieces of fastening tape.

Remove the hog rings and cover.

| 24. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System) |
![]() ![]() |
Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.
| 25. REMOVE REAR SEATBACK COVER |
![]() ![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 26. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH |
![]() ![]() |
Detach the 2 claws on the top of the board.
Pull up the board to detach the 2 claws on the bottom of the board and remove it.
| 27. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 28. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() ![]() |
Detach the 4 claws and remove the 2 supports.
| 29. REMOVE SEATBACK COVER WITH PAD |
Remove the hog rings.

w/ Rear Seat Side Airbag:

Remove the cap nut and seatback cover bracket from the seat frame.
Remove the side airbag wire harness through the hole in the seatback.
w/ Seat Heater System:
Cut the cable tie and disconnect the seatback heater wire harness.

Remove the seatback heater wire harness through the hole in the seatback.

Remove the seatback cover with pad.
| 30. REMOVE REAR SEPARATE TYPE SEATBACK COVER |
w/ Rear Seat Side Airbag:

Disconnect the seatback cover bracket from the seatback pad.
Remove the hog rings and rear seatback cover.

| 31. REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System) |
![]() ![]() |
Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.
| 32. REMOVE REAR SEAT RECLINING COVER LH |
![]() ![]() |
Remove the screw.
Detach the claw and remove the cover.
| 33. REMOVE REAR SEAT RECLINING COVER RH |
Remove the screw.
Detach the claw and remove the cover.
| 34. REMOVE REAR NO. 2 SEAT RECLINING COVER LH |
![]() ![]() |
Remove the screw.
Detach the clamp and remove the cover.
| 35. REMOVE REAR NO. 1 SEAT RECLINING COVER RH |
![]() ![]() |
Remove the screw.
Detach the claw and remove the cover.
| 36. REMOVE RECLINING ADJUSTING CABLE ASSEMBLY RH |
![]() ![]() |
Detach the 2 cable clamps and disconnect the cable.
Detach the clamp and remove the adjusting cable.
| 37. REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY |
![]() ![]() |
Detach the 2 cable clamps and disconnect the cable.
Detach the clamp and remove the lock control cable.
| 38. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH |
![]() ![]() |
Using a T40 "TORX" socket, remove the 4 bolts.
Remove the seatback frame.
| 39. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY |
![]() ![]() |
Detach the 2 cable clamps and disconnect the 2 cables.
Remove the 2 fold seat lock control cables.
| 40. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY |
Remove the 2 nuts and lower seat track bracket.

Remove the 2 nuts and lower seat track bracket.

Detach the 3 cable clamps and disconnect the 3 cables.

Detach the clamp and remove the seat lock cable.
| 41. REMOVE REAR SEAT CUSHION HOLDER BRACKET RH (w/ Seat Heater System) |
![]() ![]() |
Disconnect the seat wire connector.
Remove the 2 screws and holder bracket.
| 42. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System) |
![]() ![]() |
Detach the 2 claws and remove the seat heater control.
| 43. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH |
![]() ![]() |
Remove the bolt and belt.
| 44. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH |
![]() ![]() |
Using a T40 "TORX" socket, remove the bolt.
Remove the 5 nuts and seat cushion frame.
| 45. REMOVE REAR NO. 1 SEAT LOCK CONTROL LEVER |
![]() ![]() |
Remove the bolt and lock control lever.































