2011-2013 Land Cruiser · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER

B181206
  1. Install the lock control lever with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

B181207
  1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

  1. Tighten the 5 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Using a T40 "TORX" socket, tighten the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


3. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

B184528E01
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the seat.


4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

B182640
  1. Attach the 2 claws to install the seat heater control.


5. INSTALL REAR SEAT CUSHION HOLDER BRACKET RH (w/ Seat Heater System)

B184856
  1. Install the holder bracket with the 2 screws.

  1. Connect the seat wire connector.


6. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

B181205
  1. Attach the clamp to install the seat lock cable.

  1. Attach the 3 cable clamps to connect the 3 cables.

  1. B181204
    Install the lower seat track bracket with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. B181203
    Install the lower seat track bracket with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


7. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

B181202
  1. Install the 2 fold seat lock control cables.

  1. Attach the 2 cable clamps to connect the 2 cables.


8. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

B181201
  1. Temporarily install the seatback frame with the 4 bolts.

  1. Using a T40 "TORX" socket, tighten the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


9. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

B181200
  1. Attach the clamp to install the lock control cable.

  1. Attach the 2 cable clamps to connect the cable.


10. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY RH

B181199
  1. Attach the clamp to install the adjusting cable.

  1. Attach the 2 cable clamps to connect the cable.


11. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B181198
  1. Attach the claw to install the cover.

  1. Install the screw.


12. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

B181197
  1. Attach the clamp to install the cover.

  1. Install the screw.


13. INSTALL REAR SEAT RECLINING COVER RH

B181196
  1. Attach the claw to install the cover.

  1. Install the screw.


14. INSTALL REAR SEAT RECLINING COVER LH
  1. Attach the claw to install the cover.

  1. Install the screw.


15. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with new tack pins.

    B181208E01


16. INSTALL REAR SEPARATE TYPE SEATBACK COVER

B182659E01
  1. Using hog ring pliers, install the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B182660
    w/ Rear Seat Side Airbag:
    Connect the seatback cover bracket to the seatback pad.


17. INSTALL SEATBACK COVER WITH PAD
  1. Install the seatback cover with pad.

  1. w/ Rear Seat Side Airbag:
    Pass the side airbag wire harness through the hole in the seatback.

  1. w/ Seat Heater System:

    1. B184855
      Pass the seatback heater wire harness through the hole in the seatback.

    2. B184853E01
      Connect the seatback heater wire harness and install a new cable tie.

  1. B181192
    w/ Rear Seat Side Airbag:
    Install the seatback cover bracket to the seat frame with the cap nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

  1. B182661E01
    Using hog ring pliers, install new hog rings to the seatback frame.


18. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B181190
  1. Attach the 4 claws to install the 2 supports.


19. INSTALL REAR SEAT HEADREST ASSEMBLY

20. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

B182662
  1. Push the board down to attach the 2 claws on the bottom.

  1. Attach the 2 claws on the top of the board to install it.


21. INSTALL REAR SEATBACK COVER

B182667
  1. Attach the 4 claws to install the cover.


22. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with new tack pins.

    B181209E01


23. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

B182663E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B181184E01
    Attach the 3 pieces of fastening tape.


24. INSTALL SEAT CUSHION COVER WITH PAD
  1. Install the seat cushion cover with pad.

  1. w/ Rear Seat Side Airbag:
    Pass the side airbag wire harness through the hole in the seat cushion.

  1. w/ Seat Heater System:

    1. B184059
      Pass the seatback heater wire harness through the hole in the seat cushion.

    2. B184061
      Connect the 2 seat heater connectors.

  1. w/ Rear Seat Side Airbag:
    Attach the side airbag wire harness clamps.


25. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

26. INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY

  1. B181183
    Attach the cable clamp to connect the cable.

  1. B181182
    Attach the 2 cable clamps to connect the 2 cables.

  1. B182656
    Install the seat track handle with the 2 screws.


27. INSTALL REAR SEAT UNDER TRAY COVER RH

B181181
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


28. INSTALL NO. 1 SEAT CUSHION PLATE

B181180
  1. Attach the 3 claws to install the seat cushion plate.


29. INSTALL REAR UNDER SIDE COVER LH

B181178
  1. Attach the 2 claws and clip to install the cover.

  1. Install the 5 screws.


30. INSTALL REAR SEAT COVER

B181179
  1. Attach the 2 claws to install the cover.

  1. Install the 3 screws.

  1. B181177
    Attach the 12 claws.


31. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

  1. B181176
    Attach the cable clamp to connect the cable.

  1. B181175
    Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear Seat Side Airbag:
    Attach the wire harness clamp.

  1. w/ Seat Heater System:
    Attach the wire harness clamp.


32. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

B181174
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


33. INSTALL REAR NO. 2 SEAT PROTECTOR
  1. Install the wire harness, and attach the 2 claws to close the protector.

  1. B184060
    Attach the claw to install the protector to the seat hinge.

  1. Install the clip.

  1. B182658
    w/ Rear Seat Side Airbag:
    Attach the claw to install the wire harness connector.

  1. w/ Seat Heater System:
    Attach the claw to install the wire harness connector.


34. INSTALL REAR SEAT SIDE HINGE MALE COVER RH

B181173
  1. Attach the clip to install the cover.


35. INSTALL REAR SEAT SIDE HINGE MALE COVER LH
  1. Attach the clip to install the cover.


36. INSTALL REAR SEAT SIDE HINGE FEMALE COVER

B181172
  1. Attach the 6 claws to install the 2 covers.


37. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY
  1. Install the fold seat stopper band to the seat leg side cover.


38. INSTALL REAR NO. 2 SEAT LEG SIDE COVER

  1. B181171
    Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

  1. B181170
    Attach the 3 claws to install the seat leg side cover.

  1. Install the 4 screws.


39. INSTALL NO. 1 SEAT CUSHION COVER

B181167
  1. Attach the 4 claws to install the 2 covers.


40. INSTALL UPPER SEAT TRACK RAIL COVER RH

B182664
  1. Attach the 2 claws to install the cover.


41. INSTALL UPPER SEAT TRACK RAIL COVER LH

B182665
  1. Attach the 2 claws to install the cover.


42. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

B181166
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


43. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B182666E01
  1. Attach the 3 claws in the order shown in the illustration to install the cover.

  1. Install the 2 screws.


44. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

B181164
  1. Install the release handle with the screw.


45. INSTALL SEAT ADJUSTER BOLT COVER

B181163
  1. Attach the 2 claws to install the cover.

← DISASSEMBLY (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →