2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH
  1. Set the seatback heater with the name stamp side facing the front separate type seatback cover.

  1. w/o Climate Control Seat System:
    Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

    B180729E02

    Text in Illustration 
    *1
    Tack Pin
    *2
    Front Separate Type Seatback Cover
    *3
    Front Seatback Heater Assembly LH
    *4
    Name Stamp

  1. w/ Climate Control Seat System:
    Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

    B298408E01

    Text in Illustration 
    *1
    Tack Pin
    *2
    Front Separate Type Seatback Cover
    *3
    Front Seatback Heater Assembly LH
    *4
    Name Stamp


2. INSTALL FRONT SEPARATE TYPE SEATBACK COVER

  1. B180730E02
    Attach the fastening tape to install the front separate type seatback cover.
    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Fastening Tape

  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B180731E01
    Pass the seatback cover bracket through the hole of the front separate type seatback pad.
    Text in Illustration 
    *1
    Seatback Cover Bracket


3. INSTALL FRONT SEPARATE TYPE SEATBACK COVER (w/ Climate Control Seat System)

  1. B298259E01
    Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B180731E01
    Pass the seatback cover bracket through the hole of the front separate type seatback pad.
    Text in Illustration 
    *1
    Seatback Cover Bracket


4. INSTALL SEATBACK COVER WITH PAD

B299577E01
  1. Attach the hooks to install the seatback cover with pad.

    Text in Illustration 
    *1
    Hog Ring
    *2
    Hog Ring Pliers

  1. B180716E01
    Attach the seatback cover bracket with the nut.
    Text in Illustration 
    *1
    Seatback Cover Bracket

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    CAUTION:
    After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    Be careful not to damage the cover.

  1. B180706
    w/o Climate Control Seat System:
    Connect the connector and attach the 2 wire harness clamps.

  1. B299194
    w/ Climate Control Seat System:
    Connect the 2 connectors and attach the 4 wire harness clamps.


5. INSTALL FRONT SEAT HEADREST SUPPORT

B298589
  1. Attach the 4 claws to install the 2 front seat headrest supports.


6. INSTALL SEAT CLIMATE CONTROL CONTROLLERLH (w/ Climate Control Seat System)

B299415
  1. Attach the 4 hooks to install the seat climate control controller LH.

  1. Attach the 2 claws to connect the seat climate control blower LH.


7. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

B182646
  1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

  1. Install the 2 screws.


8. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

B180703
  1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

  1. Install the screw.


9. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

B185875E01
  1. Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

  1. Connect the connectors and attach the clamps.


10. INSTALL FRONT SEAT CUSHION SHIELD LH
  1. for Driver Side:
    Connect the connector.

  1. B180700
    Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

  1. Install the 3 screws.

  1. B180699
    Connect the 2 rubber bands.

  1. Install the 2 screws.


11. INSTALL RECLINING POWER SEAT SWITCH KNOB

B180734
  1. Attach the 2 claws to install the reclining power seat switch knob.


12. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

B180735
  1. Attach the 2 claws to install the slide and vertical power seat switch knob.


13. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)
← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →